Ground-engaging components on 2633
Ground-engaging components on 2633
The John Deere 2630 Series offer three disk models that provide a wide range of variety for all tillage applications.
Model |
2630 Disk | 2633 Disk | 2635 Disk |
| Purpose | Secondary (light duty) | Dual purpose (medium duty) | Primary (heavy duty) |
| Working depth | Up to 130 mm (5 in.) | Up to 180 mm (7 in.) | Up to 200 mm (8 in.) |
| Weight per blade | Minimum 68 kg (150 lb) | Under 13.4 m (44 ft) Minimum 86 kg (190 lb) Over 13.4 m (44 ft) Minimum 91 kg (200 lb) |
Minimum 127 kg (280 lb) |
| Blade size | 560 or 610 mm (22 or 24 in.) |
610 or 660 mm (24 or 26 in.) |
610 or 660 mm (24 or 26 in.) |
| Blade spacing | 185 or 230 mm (7.25 or 9 in.) |
230 mm (9 in.) | 230 mm (9 in.) front and 280 mm (11 in.) rear, or 280 mm (11 in.) |
| Horsepower | 23 to 36 hp/m (7 to 11 hp/ft) | 23 to 36 hp/m (7 to 11 hp/ft) | 26 to 36 hp/m (8 to 11 hp/ft) |
| Working widths | 6.3 m to 15.0 m (20.75 ft to 49.25 ft) |
6.3 m to 15.0 m (20.75 ft to 49.25 ft) |
7.2 m to 12.4 m (23.58 to 40.66 ft) |
| Operating speed | 6.5 to 11.3 km/h (4 to 7 mph) |
6.5 to 11.3 km/h (4 to 7 mph) |
6.5 to 11.3 km/h (4 to 7 mph) |
| Recommended use |
|
|
|
John Deere's 2630 Series Disks offer different blade options for soil penetration and residue sizing.
Solid-spherical blade
Cutout-spherical blade
| Blade type | Solid-spherical blades | Cutout-spherical blades |
| Recommended application |
|
|
| Recommended soil type | Light to medium soils | Heavy to medium soils |
| Benefits | Better control of soil than cone blades since less sensitive to over speeding | Chopping or trapping residue |
| Penetration | Penetrate best at a 20-degree gang angle | Penetration is excellent with a cutout blade |
The 2630 General-Purpose Disk comes equipped with front and rear solid-spherical disk blades with 230-mm (9-in.) spacing. The primary blade size is 610 mm (24 in.) x 5 mm (0.197 in.)
230-mm (9-in.) blade spacing
230-mm (9-in.) spacing, front and rear
NOTE:
Number 10 edge (inside bevel, outside grind)
51-mm (2-in.) disk gang bolts
Gang tension system
John Deere's 2630 Series Disks provide an innovative approach to tension disk gang bolts.
Residue management
As crop yields increase, so does the amount of residue after harvest. The John Deere 2630 Disk enables producers to prepare soil for planting.
Spring pack
Spring pack
John Deere’s mechanical wing control helps producers keep their frames level for five-section disks. Mechanical wing control is included in base equipment for all five-section 2630 Series Disks.
With this feature, a large spring is placed in the wing frame on each side of the disk. As the pivot point in the wing starts to raise, the spring presses against that point to keep the disk level through tough field conditions.
The red circles in the following image illustrate the area of the disk where the large spring is placed in the wing frame.
Mechanical wing control
John Deere mechanical wing control is an industry-exclusive feature. A five-section disk without mechanical wing control can show up to 75-mm (3-in.) of depth inconsistency across the wing frame.
2630 Disk in the field
2630 Disk in the field
The 2630 Series Disks offer multiple upgrades and additional items as options versus the 2620 Series Disks to enhance the machine. Check out the following video to see more about the 2630 Series Disks.
John Deere 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil type.
John Deere TruSet system is featured in base equipment for the 2630 Series Disks and Vertical Tillage Implements. TruSet side-to-side is also available and features individual section leveling.
The hydraulic rolling basket is offered with a round bar or knife-edge. The knife-edge is best for heavier, wet soil, and can be used in rocky conditions.
The 2630 Series Disks and Vertical Tillage Implements feature radial tires for the mainframes in base equipment. Radial tires are available as an option on the wing frame and stabilizer wheels. These tires are designed to offer longer wear life and help minimize compaction with a wider plate and lower inflation pressures.
Producers can choose either mechanical stabilizer wheels or TruSet hydraulic stabilizer wheels as an option. Stabilizer wheels help to maintain a consistent, level depth and are recommended for operation on rolling ground. The mechanical stabilizer wheels can be manually adjusted with a turnbuckle. TruSet with side-to-side leveling capabilities also enables operators to control the TruSet hydraulic stabilizer wheels from the cab while on the go.
Images of equipment models may be digitally or AI generated, are for illustration purposes only, and are subject to change. Equipment models shown are typically base models and may not reflect the actual product, features, options, or attachments. Equipment availability may be limited. See your John Deere dealer for additional information.
