730DDraper Platform
- Hydrafloat™ allows the operator to match changing field conditions
- Dual-knife drive system is timed
- Cutterbar is closer to the ground
Specs & Compare | ||||
---|---|---|---|---|
Select up to 4 models to compare specifications | John Deere 730D Draper Platform |
Cutterbar length | 9.3 m 30.5 ft |
|||
---|---|---|---|---|
Knife drive | Base: dual knife Optional: single |
|||
Knife speed | 490 cycles/min | |||
Pickup reel operating speeds | 6-45 rpm 137.2-cm (54-in.) reel: 5-44 rpm |
|||
Draper belts speed control | Hydraulic from cab |
Type | Rigid draper |
---|
Type | Straight-line knife drive system | |||
---|---|---|---|---|
Length | 9.14 m 30 ft |
|||
Knife drive | Base: dual knife Optional: single |
|||
Knife speed | 490 cycles/min | |||
Cutterbar tilt | Base: hydraulic, maximum tilt 9 degree (angle) | |||
Base skid shoe height |
General | ||||
---|---|---|---|---|
Number of slats | Base: six bat poly Optional: eight bat steel (for forage conditions) |
|||
Fingers | Base: nylon Optional: steel |
|||
Diameter | 1.067 m 3.5 ft |
|||
Height control | Hydraulic | |||
Speed control | Hydraulic | |||
Reel lift | Cylinder stroke: 330 mm 13 in. Total range: 391.5 mm 15.4 in. |
|||
Reel fore and aft | Cylinder stroke: 359 mm 14.1 in. Total range: 620 mm 24.4 in. |
|||
Fore of the cutterbar | ||||
Reel resume | Base | |||
Reel reverse | Base | |||
Operating speeds | 6-54 rpm | |||
Operating speeds (54-in. reel) | 5-44 rpm |
Number of slats | ||||
---|---|---|---|---|
Diameter | ||||
Height control | ||||
Speed control | ||||
Operating speeds |
Width | Rubber coated polyester with V-Guide tracking: 0.7 L 24 oz Side belts: 1.02 m 3.33 ft Center belts: 1.4 m 4.583 ft Center belt not included with SPW configuration |
|||
---|---|---|---|---|
Belt depth | ||||
Cleat height | 25.4 mm 1 in. |
|||
Operating speed | Side belts: variable up to 223 m/min 735 fpm Center belts: 212 m/min 695 fpm Center belt not included with SPW configuration |
|||
Speed control | Hydraulic from cab | |||
Center belt reverse | Base: center belt not included with SPW configuration |
Diameter | Two factory-installed options: 356 or 406 mm 14 or 16 in. Feed drum not included with SPW configuration |
|||
---|---|---|---|---|
Feed drum fingers | Heavy-duty and round with breakaway notch and retainer Diameter: 16 mm 0.625 in. |
|||
Number of fingers | 18 | |||
Auger finger platform | Dual chevron, retracting | |||
Finger reach | 152 mm 6 in. |
|||
Drum/auger reverse | Base | |||
Operating speed | 195 rpm | |||
Center cleanout door | Base |
Type | Base: electrohydraulic | |||
---|---|---|---|---|
Header height sensing on the ground | Base | |||
Header height sensing off the ground | Base |
Type | Optional: hydraulic drive | |||
---|---|---|---|---|
Fingered augers | ||||
Size |
Platform length | 10.0 m 32.9 ft |
|||
---|---|---|---|---|
Overall operating depth | 2.5 m 8.2 ft |
|||
Transport width, field position | 9.9 m 32.5 ft |
|||
Transport width on wheel, less dividers | 2.7 m 8.9 ft |
|||
Transport length, hitch extended | 12.3 m 40.4 ft |
Approximate weight |
---|
Date collected |
---|