H260 Loader | Utility Loaders | Material Handling Equipment

Features

Single-point hydraulic connection saves time

Single-point hydraulic connection on row crop tractor (closed)

Single-point hydraulic connection on utility tractor (closed)

The H240, H260, and H310 Loaders can be ordered with a single-point hydraulic connection that also incorporates the connection point for any electrical needs. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.

Concealed oil lines improve appearance and reduce damage

Concealed oil lines through boom arm

Oil lines routed through the boom arm

Oil lines routed through the torque tube

Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage.

To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.

Loader removal (parking) made easy

Parking stands

John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.

To remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, lower the parking stands and place the mast pins in the open position.

To watch a video of parking and attaching an H-Series loader click here.

Removing or parking the loader

Parking stand in stored position

Removing parking stand

Mast pin in the closed position

Rotating mast pin to the open position

Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, roll back the bucket until the mast is removed from the pocket and will clear the tires.

Mast pin in the open position

Masts rotate forward, then bucket rolled back

With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor (rotating the joystick). Disconnect or open the single-point hydraulic connector (or remove couplers if no single point is installed).

Disconnect/open single-point hydraulic connection

Disconnect/open single-point hydraulic connections

Store the loader half of the single-point connector or hoses, and back away from the loader.

Single-point hydraulics disconnected

Parked loader

Boom lockout for easy service

Hydraulic shut-off valve (open position)

Hydraulic shut-off valve (closed position)

A hydraulic shut-off valve is included with the H-Series Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.

False rod bucket cylinders improve productivity

False rod cylinder

Fast bucket cycle times are important to dump the load from the bucket as quickly as possible, (quite often) in order to be as productive as possible, while completing loading operations. The bucket cylinder design can have a major impact on this cycle time, especially for the mechanical self-leveling loaders.

Therefore, all MSL H-Series Loaders utilize false rod bucket cylinders. A false rod cylinder has a smaller displacement of oil requirement on the head end of the cylinder, which allows this cylinder to dump much faster than a normal cylinder.

Loader suspension system (LSS) to enhance the ride

Nitrogen-charged accumulator and electric valve

Operator on/off switch

LSS on H180

LSS on 5E and 5M

An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.

An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
The cylinders move in and out to allow the boom to float

Performance

Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain.

NOTE: Check bale-handling capability of tractor before use.

Pallets can be moved easily without sustaining cargo damage
Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
A properly-ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Cost of ownership

Extended life of loader pins and bushings
Less stress on tractor axle

Reasons for turning LSS off include:

Digging applications - with LSS on, the cylinders retract slightly, losing lifting power
Holding a grade when blading - with LSS on, it is difficult to hold a constant grade
Precise pallet and bale handling - with LSS on, the load moves up and down slightly while being positioned
Parking a loader - with LSS on, when down pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.

LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.

Show More Show Less