XUV865M CabCrossover Utility Vehicle

The Gator™ XUV Crossover Series Utility Vehicle has a precision-engineered drivetrain system that fully utilizes engine power, optimizing acceleration, hauling, towing, and hill-climbing capabilities. Power is transmitted from the engine through a continuously variable clutch system to the transaxle.

Key elements of the drive system include:

Variable-speed drive

Variable-speed drive

The variable-speed drive consists of two clutches and a drive belt:

• Drive clutch is attached to the engine.
• Driven clutch is attached to the transaxle.

Features include:

• The engine braking system utilizes a tight belt for operation, requiring an idler sleeve on the primary clutch for neutral. The secondary clutch is a build- on-shaft design that utilizes a cam to tune the acceleration and deceleration of the vehicle. The clutch stays engaged, providing deceleration until approximately 5 km/h (3 mph).
• The continuously variable transmission (CVT) air intake draws in cool air to reduce heat and the amount of water ingestion into the CVT system. The system reduces belt slippage and improve durability.
• A two-range transmission provides:
  • Ability to maneuver in tight spaces and increased pulling torque in low range
  • Faster speeds and reduced transport time in high range
• Standard full-clutch enclosure with high speed fan provides longer belt and clutch life
• High-ratio clutches with three cam weights for maximum belt-clamp load in high torque conditions

How the variable-speed drive works:

1. As engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
2. As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
3. With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
4. The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts drive speed upward or downward so that engine rpm remains optimal.

Transaxle, mechanical front-wheel drive (MFWD), and constant velocity (CV) shafts

Side view of CVT intake and clutch enclosure (XUV835M shown)

Differential lock switch and MFWD switches

Rear view of transaxle, suspension components, and CV shafts (XUV865M shown)

CV boot protection

Operator interface features:

• Selectable four-wheel drive (4WD) system with a limited slip front differential and dash-mounted electronic rocker switch
  • Provides exceptional traction in challenging conditions
  • Near instantaneous torque to the front wheels once rocker switch is engaged
  • Maintains turf-friendly operation in two-wheel drive (2WD) mode
  • Combined with rear traction assist (differential lock), provides excellent traction in challenging conditions
  • More control descending hills with 4WD engaged as all four wheels help slow the vehicle down
    • Clutch engagement still necessary to prevent free coasting

Transaxle features:

• Low, high, neutral, reverse, and park transaxle
• Automotive-style, integrated park position in transmission
• Low range for maximum torque delivered to the wheels for hauling, pushing, and pulling
• High range for maximum vehicle speed
• To shift out of park, service brake must be pressed to release the parking solenoid. An audible click will be heard and allows the vehicle to shift out of park into the desired gear.

NOTE: Differential design reduces scuffing of the turf during turns because it allows the inside wheels to turn slower than the outside wheels.

• Start in gear, neutral, or park position for quick starting. The service brake must be engaged to start when in gear or neutral.
• For operators living in regions with homologation requirements or certain bid language stating the need for a secondary park brake, such as governmental or municipalities, a secondary park brake is available as a factory-installed option. A secondary brake attachment is not available for field installation.
• Large, sealed bearings are located inside the housing for better protection and durability
• Contains gear case for transferring power to the MFWD
• Splined shaft interfaces for maximum torque transfer and durability
• All drive gears machined from highest grade gear steel
• Protected by a skid plate

MFWD features:

• Electronically selectable by the operator
  • Offers limited slip functionality for precision steering and great traction while pointing and shooting out of a corner.
• Vertically oriented oil drain for easy maintenance
• Protected by a steel skid plate and frame

Drive shaft features:

• Rear CV shaft diameter measures 27 mm (1.1 in.) and is designed for peak engine and braking torque
• Front CV shaft diameter measures 23 mm (0.91 in.) and is designed for peak engine torque
• Propshaft is designed for peak engine torque
• All CV shaft and propshaft joints are maintenance free and protected by exclusive thermoplastic elastomer (TPE) boots for durability

Heating, ventilation, and air conditioning (HVAC) dash shown with model year 2021 tan interior

Whether it is a completely open operator station or a factory-installed cab, the interior has been redesigned with comfort and ergonomics in mind.

• Gear shift control and differential switch on the dash

HVAC dash shown with model year 2021 tan interior (R trim)

• Tilt steering

Tilt steering

Tilt steering (up position)

Tilt steering (down position)

• Bench seat with driver adjustment

Bench seat adjustment

• Three-wide seating

Seating

Cab

M and R spec cab door

Side windows and front window

Venting position

• Functioning door windows – roll up and down
• Fully opening front window with vent position

Headliner shown on an M-trim open station (with optional windshield, wipers, rear panel, and side mirrors installed)

• Available interior roof headliner factory installed on M-trim cab units and M-trim heating, ventilation, and air conditioning (HVAC) cab units

Door sealing

• Automotive-style sealing

Styled roof (R roof shown)

• Styled roof with channels designed-in to move water to the outside edges

Front roof light

Rear roof light

• Molded-in pockets for front and rear light mounting
  • Keeps lights below the roof line for protection

Inner door handle

Outer door handle

• Easy-opening door handles and mechanisms

854-cc (52.1-cu in.) diesel engine

The machine is powered by an 854-cc (52.1-cu in.), 3-cylinder, liquid-cooled, four-cycle diesel engine. It produces 48 Nm (35.5-lb-ft) of torque at 2600 rpm.

The advanced engine delivers superb starting, idling, and throttle response during operation.

The engine offers the following performance and reliability features:

• Indirect-injection diesel with glow plugs ensures fast starts in cold temperatures
• 17.1 kW (22.9 hp*) at 3600 rpm
• Overhead valve design for greater efficiency and fuel economy
• Spin-on oil filter for easy servicing
• Quiet operation through the entire rpm range
• Molybdenum-coated pistons
• High-stiffness cylinder block and gearcase
• High-flow water pump and optimized water jackets maintain a steady operating temperature and eliminate hot spots
• Full-pressure lubrication system
• In-line mechanical fuel pump
• Five-point, rubber isolated for quiet operation and minimal vibration
• Dry replaceable dual-element air cleaner with remote intake and a restriction indicator
• See-through coolant recovery tank permits the operator to check the coolant level without removing the radiator cap
• Open front grille allows proper air flow and ventilation to the radiator.

*The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. The actual operating horsepower will be less.

XUV front suspension detail

To complement the robust frame, the XUV is equipped with four-wheel independent suspension.

A dual A-arm front and rear suspension provides a smooth ride over challenging terrain and excellent hauling characteristics.

The entire suspension system has been optimized to handle no cargo to maximum cargo without compromising ride quality or vehicle stability.

M-trim units with factory-installed cabs and R-trim units have heavy-duty front and rear shocks installed from the factory.

• A higher spring rate and higher preload force versus standard springs prevent the vehicle from sagging with a heavy payload.
• These heavy-duty shocks help with the heavier weight of the cab and when attachments are installed, like blades.

Dual A-arm independent front suspension features include:

• 201 mm (7.9 in.) of travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
• Heavy-duty nodular cast-iron knuckles support the constant-velocity (CV) shaft and wheel
• Maintenance-free rubber torsional A-arm pivots for long life and quiet operation
• CV shaft protection from sticks that may puncture the rubber boot
• Coil-over shocks absorb the most demanding terrain

XUV rear suspension detail

XUV rear suspension detail (shown on XUV865M)

Dual A-arm independent rear suspension features include:

• Unequal length and dual A-arm construction for superior wheel control and travel
• 231 mm (9.1 in.) of total travel provides ample wheel travel to keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
• Coil-over shocks absorb the most demanding terrain
• A-arms made from square/rectangular tubing reduce weight while remaining rigid
• Heavy-duty nodular cast-iron uprights support wheel loads with a double row of ball bearings
• CV driveshaft protection from sticks that may puncture the rubber boot
• Rear sway bar for lateral stability

Deluxe cargo box with optional light protectors

Top view of cargo box

The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust and dents and reduces noise.

Deluxe cargo box tailgate

Tailgate handle

Tailgate open

Tailgate lowered to 150 degrees

The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.

The standard-installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.

Deluxe cargo box tilt

Integrated handle for manual cargo box tilt

The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist.

A prop rod is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.

Integrated tie-down points

Integrated tie-down point in cargo-box bed

Additional tie-down points (TH 6X4 shown)

The deluxe cargo box offers integrated tie-down points for increased versatility. Tie-down points are located in the following areas:

• Four corners inside the cargo box bed
• Four points on the load guard directly behind the operator station (A)
• Tie-down bars on either side of the cargo box (B)
• Six points on the underside of the cargo box frame (circled)

Converting deluxe cargo box to a flatbed

XUV835M Cab shown

XUV835M Cab shown

Optional accessories for the deluxe cargo box:

• See attachment information in the Sales Manual

Specifications

CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

On M- and R-trim vehicles, adding attachments and accessories is made easier by the inclusion of some main wiring harnesses that facilitate efficient hook-up.

Roof harness electrical port

Main vehicle harness – winch connection

If dual beam headlights are desired, the following bundles are required:

XUV835E/865E:

• BM26589 – dual beam LED headlights, including three-position rocker switch
• BUC10809 – front light harness kit
• BUC10810 – E-spec attachment harness

XUV835M/865M:

• BM26589 – dual beam LED headlights, including three-position rocker switch
• BUC10809 – front light harness kit

XUV835R/865R:

• BM26589 – dual beam LED headlights, including three-position rocker switch

This Gator™ XUV Crossover Utility Vehicle is equipped with power steering and a dual A-arm front suspension. These automotive-type systems exhibit excellent handling characteristics, as well as responsive steering and low steering effort:

• Steel ball bearings secure the steering shaft and deliver smooth, responsive operation
• Completely sealed rack-and-pinion for long life
• Low steering ratio (lock-to-lock) provides more responsive steering and less operator input
• Shaft U-joints are phased for a smooth, uninterrupted motion of the steering wheel
• Tilt steering wheel with 15 degrees of travel (XUV835M, XUV835R, XUV865M, and XUV865R models only; S4 models do not have tilt steering)

Electric power-assist steering system

Electric power-assist steering (EPAS) system has advanced features:

• Anti-kickback feature reduces the amount of steering unwinding when traversing difficult terrain.
• The system is speed sensing and adjusts steering effort as the speed of the vehicle changes.
  • As speed increases, there is less steering assist for improved road feel.
  • As speed decreases, steering assist increases to give lower steering efforts for improved maneuverability.
• A warning/functional light on the instrument panel provides self-diagnostics and a warning light in the situation of no assist.
• Torque sensor measures steering wheel input so the on-board computer can provide the appropriate output for various driving situations.

With the EPAS system, the operator maintains a direct, mechanical linkage from the steering wheel to the front wheels. The power-steering system interfaces mechanically with the steering system by being inserted between the steering wheel and the rack-and-pinion assembly.

A differential torque sensor is integrated into the power steering assembly. The circuit board assembly is also integral with the power-steering assembly.

Power steering does not reduce turning radius but significantly reduces steering effort by approximately 85 percent compared to those models without power steering.

EPAS interface diagram

EPAS interface diagram

The numbered descriptions refer to the EPAS interface diagram shown above:

1. Torque sensor
2. Electronic control unit (ECU)
3. Fail-safe relay
4. Current/thermal control circuit
5. Reduction gears
6. DC motor
7. Rack and pinion
8. Function/warning light
9. Key power and ground
10. Vehicle speed sensor
11. Instrument cluster
12. Relay module

The M trim adds electrical power-assist steering (EPAS) and brings in the main wiring harness for easier attachment hook-up. Cabs are available in this trim level. Heating, ventilation, and air conditioning (HVAC) is also an option within the M-trim level.

XUV operator station

M-trim dashboard

Build-to-order options

• Roof standard on all units – can order less roof on open station units
• Available factory-installed winch on M- and R-trim units
• Available factory-installed front glass windshield on M-trim open station units
• Available factory-installed rear glass panel on M-trim open station units
• Available factory-installed brush guard
• Available factory-installed brush guard extensions
• Available factory-installed rear cargo box fender guards (rear bumper required, also factory installed)
• Available factory-installed cargo box power lift
• Available factory-installed deluxe cargo box with spray-in liner, brake lights, and taillights

StarFire™ 3000 Receiver installed on XUV835R

GreenStar™ display installed on XUV835R with optional phone and tablet mounts

The AMS integration kit allows the operator to mount a StarFire Receiver and GreenStar display (both receiver and display sold separately) to the Gator™ Utility Vehicle.

Key features of the AMS integration kit:

• Compatible with StarFire iTC, StarFire 3000, and StarFire 6000 Receivers
• Compatible with GreenStar 2 1800, GreenStar 2 2600, GreenStar 3 2630, and John Deere 4640 Universal Display
• Ability to mount receiver to the poly roof or on the occupant protective structure (OPS) alone

NOTE: Additional components are required to support the John Deere 4640 Universal Display include:

• AL212683 (1)
• 21M7577 (2)

Common applications:

• Boundary mapping
• Flagging field obstacles
• Soil sampling

Compatibility:

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements:

Cargo box pail holder

Cargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Cargo bed extender

Cargo bed extender

The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.

Deluxe cargo box bed mat

The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box divider located at rear of cargo bed

Cargo box divider located at front of cargo bed

Speedrail lock in the unlocked position

Speedrail lock in the locked position

The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.

Cargo box side extension kit

The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch. 

Product features include:

• Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m³ (26 cu ft)
• Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
  • Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
• Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
• Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
• Compatible with Gator cabs and bedliner

NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.

Sportsman case for Gator utility vehicles

Overview

This sportsman case from Black Mountain All-Terrain is a great storage upgrade to the bed of all Gator XUV Full-Size Utility Vehicles including XUV835, XUV865, XUV625, XUV825, XUV825 S4, XUV855, and XUV855 S4 models, as well as the Work Series Utility Vehicles including HPX615E, HPX815E, TE, TH, and TX models.

Benefits

• Functions as a toolbox and/or a hunting equipment storage case
• Secures and removes quickly from bed of a Gator utility vehicle or personal vehicle
• Keeps valuable items protected inside durable, protective plastic insert with foam padding and heavy fabric exterior
• Transports easily with shoulder strap and carry handles
• Customizable with two color choices: 
  • Realtree EDGE® camo with black base
  • Classic black

Additional details

• Holds two hunting accessories/instruments up to 127-cm (50-in.) in length
• Case easily attaches and detaches to cargo box with four quick-connect buckles
• Four D-rings with removable straps for easy removal from the XUV or pickup truck
• Convenient hand carry straps on top and grab handles on each end
• Made from water-resistant, mildew-resistant, and abrasion-resistant material
• Base covered with durable ballistic nylon/poly fabric that is resistant to tearing
• Oversized, corrosion-resistant zippers for durability and ease of use
• Lockable zippers allow contents to remain secure
• Top-loading design with wide opening lid allows quick access
• Acrylonitrile butadiene styrene (ABS) plastic interior frame protects valuable contents

The case is 127-cm (50-in.) long, 22.9-cm (9-in.) wide, 38.1-cm (15-in.) high, and weighs 7.7 kg (17 lb).

Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Sportsman case for Gator utility vehicles

Overview

This sportsman case from Black Mountain All-Terrain is a great storage upgrade to the bed of all Gator XUV Full-Size Utility Vehicles including XUV835, XUV865, XUV625, XUV825, XUV825 S4, XUV855, and XUV855 S4 models, as well as the Work Series Utility Vehicles including HPX615E, HPX815E, TE, TH, and TX models.

Benefits

• Functions as a toolbox and/or a hunting equipment storage case
• Secures and removes quickly from bed of a Gator utility vehicle or personal vehicle
• Keeps valuable items protected inside durable, protective plastic insert with foam padding and heavy fabric exterior
• Transports easily with shoulder strap and carry handles
• Customizable with two color choices: 
  • Realtree EDGE® camo with black base
  • Classic black

Additional details

• Holds two hunting accessories/instruments up to 127-cm (50-in.) in length
• Case easily attaches and detaches to cargo box with four quick-connect buckles
• Four D-rings with removable straps for easy removal from the XUV or pickup truck
• Convenient hand carry straps on top and grab handles on each end
• Made from water-resistant, mildew-resistant, and abrasion-resistant material
• Base covered with durable ballistic nylon/poly fabric that is resistant to tearing
• Oversized, corrosion-resistant zippers for durability and ease of use
• Lockable zippers allow contents to remain secure
• Top-loading design with wide opening lid allows quick access
• Acrylonitrile butadiene styrene (ABS) plastic interior frame protects valuable contents

The case is 127-cm (50-in.) long, 22.9-cm (9-in.) wide, 38.1-cm (15-in.) high, and weighs 7.7 kg (17 lb).

Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Rear fender flare kit on XUV865

Rear fender flare kit

A – Fender flare

B – Fender

The rear fender flare kit minimizes debris from reaching the operator station.

Product features include:

• Two pliable fender flares (one for each side)
• Hardware for mounting on the sides
• Compatible with all model year 2011 to current Gator™ XUV825, XUV825 S4, XUV855, XUV855 S4, XUV835, and XUV865 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles

Tool rack

Tool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detail

Adjusting the tool rack holder

Spare tire carrier

Spare tire carrier

Easily mount a spare tire to the side of the cargo box with this convenient kit.

Recommended to carry spare front tire, as the front tire can be mounted on either the front or rear hubs.

Cargo box power lift kit shown in full up position

Overview

The Gator™ utility vehicles can be equipped with an optional power lift for the cargo box. This is one of the most important accessories for increasing work efficiency. It is an excellent complement to these highly capable utility vehicles.

Benefits

• Capable of lifting a maximum vehicle cargo box load of 454 kg (1000 lb)
• Lifts box to 49 degrees from horizontal for ease of service and cargo box load removal
• Quick horizontal-to-49-degree time
• Can be installed in minutes using the vehicle's prewired connectors and mounting points
• Compact design fits nicely around the transmission and linkages, providing full protection
• Fully sealed and weatherproof design does not require maintenance and is built for maximum durability
• Overload protection protects against misuse

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Bench seat cover (shown in black)

Modular lightweight load-carrying equipment (MOLLE) attachment location

Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits

• Protection for the bench seat from wear and stains
• Constructed with military-grade CORDURA® fabrics
• Quick and easy installation
• MOLLE attachment locations (MOLLE attachments available through Order Zone)
• Easy access to seatbelts
• Available in three color options: black, Realtree EDGE® camo, or coyote brown

Additional details

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Ordering information

Available through Order Zone.

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Bench seat cover (shown in black)

Modular lightweight load-carrying equipment (MOLLE) attachment location

Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits

• Protection for the bench seat from wear and stains
• Constructed with military-grade CORDURA® fabrics
• Quick and easy installation
• MOLLE attachment locations (MOLLE attachments available through Order Zone)
• Easy access to seatbelts
• Available in three color options: black, Realtree EDGE® camo, or coyote brown

Additional details

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Ordering information

Available through Order Zone.

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

High-performance sport seat cover - black

High-performance sport seat cover - camo

High-performance sport seat cover - coyote

Each kit (available through Order Zone) contains one bench base cover, one backrest cover, and installation instructions.

NOTE: One carton (two kits) outfits driver and passenger seats.

Special features:

• Exceptional abrasion, tear, and puncture resistance
• Constructed with military-grade CORDURA® fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in black or Realtree Hardwoods HD® pattern
• Military-grade zippers
• Limited 1-year warranty
• Made in the USA

Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd. CORDURA is a trademark of INVISTA North America, LLC.

Vehicle storage cover

Vehicle storage cover

Key features

• All-season protection against sun damage, rain, dust, and tree sap
• Reinforced corners for added durability
• Fabric coated for maximum water resistance and repellency
• Elastic shock cord in bottom hem for a quick, custom fit

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Ordering information

Available through Order Zone

Drawbar kit for receiver hitch

Description:

• Kit includes a 51-mm (2-in.) drawbar, 10-mm (0.39-in.) pin, and hair cotter pin
• Steel construction has a 25-mm (1-in.) ball hole size
• Can be mounted in the standard rear receiver hitch or the optional front receiver hitch
• Compatible with all Gator model year 2011-current XUV560, XUV560 S4, XUV590, XUV590 S4, XUV 625i, XUV 825, XUV 855, RSX860, and M-Gator™ A2 Utility Vehicles
• Compatible with HPX 615 and 815 Utility Vehicles
• Compatible with XUV 620i and XUV 850D Utility Vehicles

NOTE: Compatible with all Gator HPX Utility Vehicles if equipped with an optional 51-mm (2-in.) front receiver hitch. An optional 51-mm (2-in.) rear receiver is not available for the Gator HPX models. A 32-mm (1-1/4-in.) rear receiver hitch and drawbar are available for the Gator HPX models.

Left floor mat

Right floor mat

Key features

• Kit includes left and right floor mats
• Made from 8-mm (5/16-in.) thick textured rubber
• Tool-less install and easy removal for cleaning
• Helps further dampen operator station noise

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Hood rack

Hood rack (hinged forward)

Key features

• 124.5-cm (49-in.) long x 36-cm (14.25-in.) wide x 11-cm (4.25-in.) deep
• Welded steel tubing
• Design allows for convenient tie-down points to secure load
• 45-kg (100-lb) capacity

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Requires brush guard to be installed

Brush guard

Quick pull pins

Brush guard hinged forward

Auxiliary lights mounted on brush guard (sold separately)

Key features

• Provides a modern and aggressive appearance
• Heavy-duty, 44.45-mm (1.75-in.) diameter, steel tube construction
• Welded steel brush guard provides protection for the front grille, lights, and hood
• Easy-to-use quick pull pins allow the brush guard to be hinged forward to gain access under the hood
• Includes mounts for auxiliary light-emitting diode (LED) lights (sold separately)

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Brush guard extensions

Brush guard extensions

Brush guard with extensions hinged forward

Brush guard with extensions

Key features

• Enhances the aggressive appearance of the vehicle
• Easily attaches to the brush guard (required – sold separately)
• Provides additional protection to the side hood and fender area without adding additional overall width to the vehicle
• Still allows full entry under the hood when brush guard is hinged forward

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cargo box fender guards

Key features

• Connects with rear bumper (required – sold separately)
• Provides enhanced styling in addition to heavy-duty protection to the side of the cargo box

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Front CV guards

Rear CV guards

Key features

• Kit contains both front and rear CV guards
• Additional added protection for the A-arms and CV joints
• High-strength, formed steel guards handle impacts while maintaining a low, unsprung mass to provide exceptional ride quality
• Easily bolts to the A-arms
• Drainage holes on the bottom of the guards prevent buildup of dirt, grass, and other loose materials

Compatibility

• Model year 2020 and newer XUV835 and XUV865 Utility Vehicles

Front fender guards - shown with brush guard (required) and brush guard extensions (optional)

Key features

• Easily attaches to the brush guard (required – sold separately)
• Provides protection to the front fender area
  • NOTE: With fender guards installed, the overall width of the vehicle increases to 1.75 m (69 in.).

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Rear bumper kit (TH 6X4 shown)

The rear bumper offers stylish, heavy-duty rear protection to the vehicle.

Compatible with:

• Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
• Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
• Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles

Rear CV guards

CV guards add additional protection for the A-arms, brake lines, and CV half shafts:

• Formed steel guards handle impacts while maintaining a low unsprung mass
• Easily bolt to the A-arms with six bolts
• Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
• Compatible with all model year 2011 to current Gator™ XUV625i, XUV825, XUV855, and M-Gator A2 Utility Vehicles
• Compatible with model year 2013 to current Gator XUV825 S4 and XUV855 S4 Utility Vehicles
• Compatible with model year 2018 to current Gator XUV835 and XUV865 Utility Vehicles

Rear-panel glass protector

Key features

• Provides protection to the cab rear-panel glass
  • NOTE: Never carry loads in the cargo box over the load guard.
• Perforated, black metal screen easily attaches to the cab rear panel (required – sold separately)

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Brake and taillight protector

The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.

Front attachment harness

The front attachment harness includes connections for the following kits:

• Light-emitting diode (LED) headlights
• Turn signals
• Horn
• Brush-guard-mounted auxiliary lights

Dash port harness connection

Dash port harness – lower connectors

Key features

• The front attachment harness (dash port) includes connections for the following kits:

• Rear sprayer
• Rear spreader
• Blades
• GreenStar™ Display as part of the Ag Management Solutions (AMS) integration kit

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Hydraulic blade and rear winch harness

Key features:

• The hydraulic blade and winch harness includes connections for the following kits:

• Hydraulic blade
• Winch

Compatibility:

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Rear cab attachment harness

Key features

• The rear cab attachment harness includes connections for the following kits:

• Rear auxiliary lights
• Beacon light
• Ag Management Solutions (AMS) receiver harness

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Heater vent locations (heater shown on export vehicle)

Heater switch

Key features

• Four 5.1-cm (2-in.) adjustable vents, located for defrost and floor heat
• High and low fan speeds

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Horn

Horn switch

Key features

• Frequency: 410 Hz
• Sound pressure level: 100+ dB(A)
• Water-sealed type

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

Beacon light in up position

Beacon light in down position

Backlit beacon light switch

Key features

• 76-mm (3-in.) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
• Especially useful for working around properties and job sites
• Acrylic amber lens resists scratching and scuffing
• Impact-resistant nylon housing
• Society of Automotive Engineers (SAE) J845 (Class 3)-compliant
• UL® recognized
• Flash rate: 60 +/- 10 fpm
• Stands 21.3-cm (8.4-in.) tall from roof/occupant protective structure (OPS)
• Folds down out the way when not in use

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

UL is a trademark of UL LLC.

LED headlights

Three-position backlit light switch

Key features

• Upgrade from halogen headlights
• High/low beam
• Raw lumen output (per light): 1,075 (high beam), 430 (low beam)
• Effective lumen output (per light): 720 (high beam), 240 (low beam)
• Nominal LED color temperature: 5000 K
• Current draw: 1.14 amps (high beam), 0.41 amps (low beam)

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• Model year 2021 and newer XUV560E, XUV560E S4, XUV590E, XUV590E S4, XUV590M, and XUV590M S4 Utility Vehicles

Electrical harness requirements

Front cab mounted

Rear cab mounted

Brush guard mounted

Key features

• The LED driving lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
• Beam pattern: driving (focused, intense beam of light good for illuminating a stretch of road directly in front of the vehicle)

Driving beam pattern – mounted on brush guard

Driving beam pattern – mounted on OPS/roof

• Lamp sealing: IP69K
• Light output (per light): 1150 lumens
• LED color temperature: 5000 K
• Amp draw (per light): 1.4 amps
• 6 LEDs per light
• Aluminum housing

Compatibility

• Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• HPX Utility Vehicles

Front cab mounted

Rear cab mounted

Brush guard mounted

Key features

• The LED work lights can be mounted on the front occupant protective structure (OPS), front cab, rear OPS, rear cab, or brush guard
• Beam pattern: flood (spread of light over a wider, shorter distance)

Flood beam pattern – mounted on OPS/roof

• Lamp sealing: IP69K
• Light output (per light): 1200 lumens
• LED color temperature: 5000 K
• Amp draw (per light): 1.4 amps
• 6 LEDs per light
• Aluminum housing

Compatibility

• Model Year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model Year 2018 to current XUV835 and XUV865 Utility Vehicles
• Model Year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• HPX Utility Vehicles

Rearview mirror

Key features

• Convex mirror reflects a wide-angle image to help the operator see behind the vehicle
• Connected to ball stud for easy adjustment

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Side mirrors – open station

Side mirrors – open station

Side mirrors – cab door

Side mirrors – cab door

Key features

• Kit allows mirrors to be installed on either an open-station or cab vehicle
• Mirrors can be easily adjusted based on operator preference

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Accessory mounting bracket (shown with tablet and cell phone mount)

Key features

• Allows the cell phone and tablet mount to be installed in the upper dash location
• Required for cell phone mount if mounted in the lower dash location

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Cell phones, global positioning system (GPS), and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator station.

RAM X-Grip holder

For proper machine operation, it is critical that accessory devices and tools be located and mounted where they are accessible but do not interfere with visibility and controls. The new RAM® mount kit has been specially developed to meet this need in John Deere tractors and now utility vehicles.

Simply remove the large wing nut from the assembly, insert the stud into any open hole in the occupant protective structure (OPS), and tighten down the jam nut.

Key benefits:

• Patented RAM X-Grip™ holder fits most cell phones and similar devices including iPod®, iPad®, iPhone®, BlackBerry®, Samsung Galaxy® and others.
• Mounts to the holes in the OPS
• Ball joints allow for variable positioning
• Holds firm even in rugged terrain
• The holder is compatible with many other RAM® products with their B size or 25.4-mm (1-in.) ball accessories

RAM X-Grip

The RAM X-Grip has a clean and clever four-leg design that sports great holding power without hiding the phone behind foam pads and plastic.

Features:

• Rustproof
• High-strength composite and stainless-steel construction
• Spring-loaded holder expands and contracts for custom fit
  • Minimum width: 1.875 in. (47 mm)
  • Maximum width: 3.25 in. (82 mm)
  • Depth: 0.875 in. (22 mm)
• Rubber-coated tips will hold device firm and stable
• Easy access grip knobs for quick release of your device

Warranty:

90 days, limited.

RAM and RAM X-Grip are trademarks of National Products Inc. iPad, iPod, and iPhone are trademarks of Apple, Inc. BlackBerry is a trademark of Research In Motion Limited (RIM). Samsung Galaxy is a trademark of  Samsung Electronics Co.

Visors (shown on R-spec)

Visors (shown on R-spec)

Key features

• Shades occupants from the glare of sunlight
• Hinged design
• Tan color
• Kit includes left and right visor. Rearview mirror kit required for installation.

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Tablet mount – upper mount location (shown with cell phone mount – sold separately)

Tablet mount – lower mount location (shown with cell phone mount – sold separately)

Key features

• Keeps tablet at the operator’s fingertips for doing jobs such as soil sampling
• Utilizes a RAM® mount to easily move tablet to desired location

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

RAM is a trademark of National Products, Inc.

Upper speakers

Subwoofer

Bluetooth® microphone

SiriusXM® Radio antenna/tuner

Key features

• Kit includes:
  • Wiring harnesses
  • SiriusXM® radio antenna/tuner (XM ready head unit required – sold separately)
  • Two 13.3-cm (5.25-in.) upper speakers
  • Subwoofer
  • Bluetooth® wireless microphone
• Jensen® speakers
  • Waterproof
  • 45-W root mean square (RMS) power each
  • 135-W peak power each
• Jensen subwoofer
  • Waterproof
  • 20.3-cm (8-in.) amplified subwoofer
  • Maximum power: 200 W
  • Aluminum mesh grille
  • Aluminum housing
• The head unit is sold separately through Parts. The operator must choose one of the following two head units to complete the stereo:
  • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM satellite radio, and Bluetooth technology
  • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth technology

NOTE: Must order head unit through Parts.

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
• Requires base radio kit

SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc. Jensen is a trademark of Electronics Trademark Holding Company LLC.

Lower left speaker

Lower right speaker

Head unit (sold separately) installed

Key features

• Kit includes:
  • Wiring harness
  • AM/FM antenna
  • Head unit mounting bracket
  • Two 13.3-cm (5.25-in.) speakers
• Jensen® speakers
  • Waterproof
  • 45-W root mean square (RMS) power each
  • 135-W peak power each
• The head unit is sold separately through Parts. The operator must choose one of the following three head units to complete the stereo:
  • SWJHD1130 – heavy-duty stereo with AM/FM, weatherband, and auxiliary input
  • SWJHD1635BT – heavy-duty stereo with AM/FM, weatherband, auxiliary input, SiriusXM® satellite radio, and Bluetooth® wireless technology
    • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.
  • SWJHD36AMIC – heavy-duty stereo with AM/FM, weatherband, compact disc (CD), auxiliary input, SiriusXM satellite radio, USB 2.0, and Bluetooth wireless technology
    • NOTE: To complete the SiriusXM system, please order SWR169159 antenna and SWSXV200B tuner.

NOTE: Must order head unit through Parts.

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles

Jensen is a trademark of Electronics Trademark Holding Company LLC. SiriusXM is a trademark of Sirius XM Radio Inc. Bluetooth is a trademark of Bluetooth SIG, Inc.

Roof headliner

Roof headliner installation

Key features

• Enhances the appearance of the operator station with a molded, soft-touch, automotive-style roof headliner
• Made from 3.175-mm (1/8-in.) thick sound-dampening material for improved occupant comfort
• Easily attaches to the roof with cap screws and push darts

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Bench seat cover (shown in black)

Modular lightweight load-carrying equipment (MOLLE) attachment location

Overview

Bench seat covers are available for full-size Gator™ utility vehicles.

Benefits

• Protection for the bench seat from wear and stains
• Constructed with military-grade CORDURA® fabrics
• Quick and easy installation
• MOLLE attachment locations (MOLLE attachments available through Order Zone)
• Easy access to seatbelts
• Available in three color options: black, Realtree EDGE® camo, or coyote brown

Additional details

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Ordering information

Available through Order Zone.

CORDURA is a trademark of INVISTA North America, LLC. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Bench seat cover

Key features

• Protection for the bench seat from wear and stains
• Elastic-hem cord closure for easy adjustment
• Easy access to seatbelts

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Ordering information

Available through Order Zone

Comfort straps

Kit includes two comfort straps for the left and right seat belts.

• Provides relief to the operator's and passenger's upper body when driving over rough terrain by allowing the seat belt to stretch when the seat belt locks
• Moves the upper mounting point of the seat belt down 6 in. (152 mm)
• Can be mounted to both the driver- and passenger-side upper mounting point of the three-point seat belt
• Compatible with all model year 2017 - current Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, and RSX860i Utility Vehicles when equipped with standard Occupant Protective Structure (OPS)
• Compatible only with standard Occupant Protective Structure (OPS), for deluxe cab frame, order BM22703

Wheel spacer kit

• The wider 26x12-12 tires, used in combination with four-wheel steering, on the X729, X739, and X749 Tractors do not allow adequate clearance for the tire chains, so the wheel spacer kit is required.
• Spacers simply bolt to the axle hub and the wheels to the spacer.
• BM22725 may also be used in all applications where the BM18021 wheel spacer kit has been used.
• BM22725 has additional hardware and an updated operator's manual compared to the BM18021 wheel spacer kit.
  • BM18021 was developed for use on the 400 Series (425, 445, and 455) Four-Wheel Steer Tractors for installing tire chains on the 4WS models when using 23x10.50-12 rear tires.
• The wheel spacer kit must be removed for use with the 54-in. (137-cm) Mower Deck on X700 Tractors.

45-gal. (170-L) Gator bed sprayer

The 45-gal. (170-L) Gator bed sprayer is designed to work with the Gator vehicles equipped with the steel bed or deluxe cargo box. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 43-in. boom that sprays a 120-in. swath. It's equipped with a 20-ft hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft. It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no tools mount.

Special features:

• 45-gal. (170-L) capacity
• Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
• Brackets allow boom height adjustment
• 100 psi SHURflo diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
• The fully adjustable brass spray wand tip achieves streams up to 30 ft
• Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• On/off switch located near operator
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

45-gal. (170-L) Gator bed sprayer
Order number: LP20852

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

High-performance 45-gal. (170-L) Gator bed sprayer

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).

High-performance features:

• 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
• Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
• Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
• Choice of booms (sold separately)
• On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
• 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

170-L (45-gal.) Gator bed sprayer

The sprayer is a self-contained unit that allows the user to spray trees and shrubs with the spray wand or broadcast spray in a 3.05-m (10-ft) swath with the spray boom.

Key features

• Shurflo pump operates at 6.9 bar (100 psi) and pumps 8 L/min (2.1 gpm)
• Spray boom is easily removed when not needed
• Fully adjustable brass spray wand tip achieves streams up to 9.15 m (30 ft)
• Mounts without the use of tools
• Brackets secure to Gator bed, no bungees required
• A built-in sump is provided to completely clean out the spray material
• Includes Gator accessory wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Check valves in boom tips prevent siphoning and dripping
• Equipped with a 5.8-m (19-ft) hand wand hose for convenience
• Large threaded cap makes filling up easy
• Easy-to-read gallon marks are molded in

Ordering information

Contact your local John Deere dealer for availability and pricing information.

170-L (45-gal.) Gator bed sprayer
Order number: LP20851

340-L (90-gal.) Gator bed sprayer

The 340-L (90-gal.) Gator bed sprayer is designed to work with any Gator model with load capacities of 363 kg (800 lb) or greater. Extreme capacity is great for athletic fields, a farmette, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 109-cm (43-in.) boom that sprays a 3.05-m (10-ft) swath. Engineered brackets secure the sprayer to the Gator bed with no tools or additional tie-downs required.

Special features:

• 340-L (90-gal.) capacity (custom brackets and plumbing combines two 170-L [45-gal.] tanks)
• Brackets secure to Gator bed, no tools or additional strapping required after initial setup
• Brackets allow boom height adjustment
• 8-L/min (2.1-gpm) Shurflo diaphragm-type pump with 6.9-bar (100 psi) shutoff can be run dry without damage
• Fully adjustable brass spray wand tip achieves streams up to 9.15 m (30 ft)
• Equipped with a 5.8-m (19-ft) hand wand hose with side mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• On/off switch located near operator
• 12-V plug included with wiring harness for convenient electrical hookup
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact a local John Deere dealer for availability and pricing information.

340-L (90-gal.) Gator bed sprayer
Order number: LP20853

Viton is a trademark of The Chemours Company FC, LLC. Santoprene is a trademark of Exxon Mobil Corporation.

340-L (90-gal.) high-performance bed sprayer

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 340-L (90-gal.) capacity, high-volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 7.3-m (24-ft) boomless spray nozzles (LP22884).

High-performance features:

• 6.9-bar (100-psi), 15.1-L/min (4-gpm) SHURflo diaphragm-type pump is designed for high hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single hand mist to 10.7-m (35-ft) stream
• Equipped with a 6.1-m (20-ft) hand wand hose with side mount hose tender for convenience
• Glycerin-filled pressure gauge and TeeJet® pressure regulation/recirculation valve
• Choice of booms (sold separately)
• On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
• 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Brackets secure to Gator bed, no tools or additional strapping required after initial setup
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact a local John Deere dealer for availability and pricing information.

340-L (90-gal.) high-perfromance Gator bed sprayer
Order number: LP22909

TeeJet is a trademark of Spraying Systems Co. Viton is a trademark of The Chemours Company FC, LLC. Santoprene is a trademark of Exxon Mobil Corporation.

340.7-L (90-gal.) single tank sprayer

The high-performance (HP) single-tank 340.7-L (90-gal.) Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box that have a capacity in excess of 362.9 kg (800 lb). The custom molded 340.7-L (90-gal.) tank provides a low profile with capacity perfect for athletic fields, farmettes, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. Custom engineered mounting hardware ensures the unit stays secure without the use of additional straps or tie-downs. Cover ground quickly with flexible boom options. (Boom sold separately).

High-performance features:

• 100 psi, 4-GPM diaphragm-type pump is designed for high-hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single-hand mist to 10.7-m (35-ft) stream.
• Side-mount hose tender for easy hose access and storage
• Glycerin-filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve for precise sprayer calibration

Additional features:

• Custom engineered brackets secure to Gator bed with no tools or additional straps
• Control valve channels spray to either the boom or spray wand
• Includes Gator accessory wiring harness, complete with quick disconnects, for convenient electrical hookup
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

340.7-L (90-gal.) sprayer on XUV835

Overview

The 341-L (90-gal.) rate controlled sprayer for Gator™ utility vehicles is proof that the evolution of modern sprayers is correlated to progress in electronics and forward thinking. By utilizing pulse width modulation (PWM) technology, like the systems found on large-scale ag sprayers, this sprayer provides many of the same features and benefits to operators with XUV835 and XUV865 Full-Size Crossover Utility Vehicles.

Benefits

• Greater productivity due to faster travel while spraying
• Easier adjustments through advanced controls using the 8.1-cm (3.2-in.) display
• Savings on chemical costs thanks to more consistent application rate
• Lower risk of environmental contamination because of precision spray rate

Additional details

With this sprayer, operators effortlessly maintain their application rate without needing to hold a constant ground speed. For example, if the operator slows down to maneuver around an obstacle, the solenoid valves on the sprayer tips compensate by decreasing the rate of material being applied. If the operator stops the vehicle, the solenoid valves shut the tips off completely and the spray returns to the tank through a return valve. This precise measuring of the Gator utility vehicle’s speed is done through a controller area network (CAN) bridge (BUC10316), which provides instantaneous communication between the sprayer and the vehicle.

For simple operation, an 8.1-cm (3.2-in.) display mounts to the vehicle’s dash. This display allows operators to easily select a spray mode (boom or wand), adjust the speed range, tip size, and flow rate, and individually activate or deactivate tips for more application options. After setup, the minimum and maximum speed ranges are shown as a horizontal meter to help the operator avoid traveling too fast or too slow based on their set parameters.

Partnering with this technology is a proven 20-L/min (5.3-gpm) Shurflo® pump that provides up to 4.1 bar (60 psi). Material is applied as wide as 3.8 m (12.5 ft) with a durable, spring-loaded folding steel boom. Also included is a deluxe hand wand with a brass tip that provides both cone and stream spray patterns. Attached to the wand is 9.1 m (30 ft) of hose that is ideal for spot spraying weeds as far 10.7-m (35-ft) away and trees up to 9.1-m (30-ft) high.

Key features

• Rate control technology – allows operators to effortlessly hold their application rate without worrying about maintaining exact ground speed.
• 8.1-cm (3.2-in.) display – provides operators with the ability to select a spray mode (boom or wand), adjustments to the speed range, tip size, and flow rate, and individually activate or deactivate tips for greater application options.
• Pressure control through return valve – helps maintain the droplet size defined by the spray tip, which is important as some materials require different droplet sizes.
• Individual tip shutoff – provides greater options for different spraying applications.
• Shurflo 20-L/min (5.3-gpm) pump – is designed for high-hour commercial applications and provides up to 4.1 bar (60 psi) on demand.
• Spring-loaded, folding steel boom – applies up to 3.8-m (12.5-ft) spray swath. Five XRC TeeJet® nozzles are used to prevent dripping that can lead to spotting.
• Adjustable hand wand – features a brass tip with a spray pattern that can be adjusted from cone to stream, perfect for spraying trees, weeds, and hard-to-reach places.

Compatibility

• Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles

Specifications

Components included

• 341-L (90-gal.) sprayer assembly
• 3.8-m (12.5-ft) boom and support components
• 9.1-m (30-ft) deluxe hand wand
• Controller and mounting plate
• 8.1-cm (3.2-in.) display
• Display mounting bracket
• Dash, chassis, and sprayer harnesses
• Hardware
• Operator's manual

Required John Deere parts

• E-Spec Full-Size Crossover Gator Utility Vehicles (XUV835E and XUV865E)
• Dash port attachment harness (BM26268)
• E-Spec attachment harness (BM26266)
• CAN bridge (BUC10316)
• M-Spec Full-Size Crossover Gator Utility Vehicles (XUV835M and XUV865M)
• Dash port attachment harness (BM26268)
• CAN bridge (BUC10316)
• R-Spec Full-Size Crossover Gator Utility Vehicles (XUV835R and XUV865R)
• Dash port attachment harness (BM26268)
• CAN bridge (BUC10316)
• Shurflo is a trademark of Pentair Flow Technologies, LLC. TeeJee is a trademark of Spraying Systems Co. Viton is a trademark of The Chemours Company FC, LLC.

Sprayer wiring kit components

Overview

This sprayer wiring kit provides plug-and-go functionality for customers with Full-Size Crossover Gator Utility Vehicles with deluxe cargo boxes and compatible sprayers. Instead of connecting a sprayer's wiring directly to the battery, this kit utilizes the vehicle's pre-installed wiring for a cleaner initial installation and simplified routine attachment afterwards.

Benefits

• Plug-and-go compatibility utilizing the vehicle's pre-installed wiring instead of connecting directly to the battery
• Convenient dash-mounted switch puts on/off control of a sprayer within short reach

Additional details

Included with each kit are four harnesses. Two (the upper and lower harnesses) are for the on/off rocker switch, which can be installed in one of the blank switch plates on the vehicle's dash. The chassis harness runs along the rear of the chassis, extending power and data ports to the back corner of the vehicle. Lastly, the sprayer harness connects to the chassis harness and runs to the sprayer pump, providing a clean and tidy wiring solution.

Compatibility

• Model year 2018 and newer Gator XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Full-Size Crossover Utility Vehicles
• Sprayers:
  • LP33597 – 94.6-L (25-gal.) sprayer for Gator utility vehicles
  • LP20852 – 170.3-L (45-gal.) sprayer for Gator utility vehicles
  • LP22908 – 170.3-L (45-gal.) deluxe sprayer for Gator utility vehicles
  • LP48006 – 341-L (90-gal.) deluxe sprayer for Gator utility vehicles
  • LP20853 – 341-L (90-gal.) dual-tank sprayer for Gator utility vehicles
  • LP22909 – 341-L (90-gal.) deluxe dual-tank sprayer for Gator utility vehicles

Components included

• Upper dash harness
• Lower dash harness
• Rocker switch (on/off)
• Rocker switch sticker
• Chassis harness
• Sprayer harness
• Hardware (includes zip ties and wire harness clips)
• Installation instructions

Required John Deere parts

• E-Spec Full-Size Gator Utility Vehicles (XUV835E and XUV865E)
• Dash port attachment harness (BM26268)
• E-Spec attachment harness (BM26266)
• M-Spec Full-Size Gator Utility Vehicles (XUV835M and XUV865M)
• Dash port attachment harness (BM26268)
• R-Spec Full-Size Gator Utility Vehicles (XUV835R and XUV865R)
• Dash port attachment harness (BM26268)

0.3-m3 (10-cu ft) in-bed spreader for XUV835 and XUV865

Overview

The 0.3-m³ (10-cu ft) in-bed spreader easily expands the capabilities and productivity of operators with Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles. Featuring exclusive controls and ample hopper capacity, these spreaders are the ideal spreading solution to help operators quickly apply large amounts of ice melt materials.

Benefits

• Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof, color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds, vibratory motor settings, auger reverse to clear out jammed material, and unload mode to completely empty the hopper. The display easily mounts to the vehicle's dash by utilizing existing holes.
  • If a controller area network (CAN) bridge (BUC10316) is installed on the utility vehicle, operators can access automatic stop, which halts spreader operation when the vehicle stops moving.
• Enjoy long periods of spreading ice melt materials with the ample volume of the 0.3-m³ (10-cu ft) poly hopper.
• The 7.6-cm (3-in.) diameter steel auger is powered by a direct-drive motor and features variable speed control, automatic jam clearing, and reverse to clear jammed material.
• Quickly cover large areas up to 9.1-m (30-ft) wide using the 30.5-cm (12-in.) diameter steel spinner with independent speed control.
  • This entire assembly can be quickly disconnected to access the vehicle's hitch and reduce the spreader's overall footprint for storage.
• Eliminate bridged material inside the hopper with the vibratory motor that features four modes (pulse, low, high, and ramp).
• A top screen and fitted tarp are included to help with material handling. The top screen prevents clumped material from entering the hopper, while the fitted tarp helps keep material dry.
• Get a dedicated, secure fit to the cargo box from the provided mounting hardware. Two stainless-steel tie-down rods secure the spreader to the tie-down hooks in the bed.

Additional details

The 0.3-m³ (10-cu ft) in-bed spread is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

17AT Cart

• 0.5-m ³ (17-cu ft) capacity
• 453.6-kg (1000-lb) load limit
• Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
• Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
• Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
• Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
• Heavy-duty polyethylene bed
  • Accepts dividers to separate cargo (template included)
• All-terrain knobby tires
  • Provides good flotation and traction in mud, sand, and other wet or soft areas
  • Flexes over bumps and ruts for a smoother, more controlled ride
  • Minimizes ground compaction to save turf and prevent ruts in soft ground
• Poly fenders to keep the operator, cart, and vehicle clean
• Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1.875-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
• Quality and styling compatible with other John Deere equipment

Ordering information

Contact your local John Deere dealer for availability and pricing information.

17AT Cart

Order number: LPPCT17ATJD

0.14-m3 (5-cu ft) drop spreader

Overview

Whether it's a snow removal contractor, a grounds crew at a college campus, or a municipality working downtown, a drop spreader is a professional's choice for precision spreading. This drop spreader combines a large, 0.14-m³ (5-cu ft) material capacity with a precise 109-cm (43-in.) spread width that's ideal for salting sidewalks. Heavy-gauge stainless-steel construction, simple drives, and an industry-exclusive removable rotor tray make this attachment the ultimate spreading solution.

Benefits

• Enjoy long periods of spreading with the stainless-steel hopper that offers 0.14-m³ (5-cu ft) of material capacity.
• The stainless-steel rotor is segmented to enhance the accuracy of material distribution with the 109-cm (43-in.) spread width.
• Simple, enclosed drives help enhance the spreader's longevity.
• Get perfect, tool-free selection of material flow with a six-position gate.
• Experience an easy, tool-free cleanout from the industry-exclusive removable rotary tray.
• Eliminate material bridging with the vibration motor.
• Enhance productivity with the multipurpose use of the spreader. Use it in the winter to spread ice-melt material and in the summer to apply fertilizer, topsoil, and lime.

Additional details

The 0.14-m³ (5-cu ft) drop spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this spreader to a XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

Specifications:

• Hopper capacity: 159 kg (350 lb), varies by material
• Rotor speed: 1.3 to 6 rpm
• Electrical: 12 V

0.085-m3 (3-cu ft) fertilizer spreader

Overview

The 0.085-m³ (3-cu ft) fertilizer spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is ideal for applying fertilizer, seed, herbicide, and other fine-particle materials. This spreader features a poly hopper with up to 109 kg (240 lb) of material capacity to minimize refilling. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 6.1 m (20 ft).

Benefits

• Enjoy long periods of spreading with a poly hopper that offers 109 kg (240 lb) of material capacity.
• Get long-term durability from the stainless-steel, 25.4-cm (10-in.) diameter spinner.
• Control the flow of fine materials through the adjustable gate operated with an electric actuator.
• Control the spread pattern with the side deflector.
• Satisfy heavy-duty spreading demands using the 1/4-kW (1/3-hp), semi-sealed electric motor.
• Improve durability in rugged conditions with a powder-coated steel frame.

Additional details

The 0.085-m³ (3-cu ft) fertilizer spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this fertilizer spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

0.085-m3 (3-cu ft) salt spreader

Overview

The 0.085-m³ (3-cu ft) salt spreader for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles is the convenient spreading solution for applying rock salt in winter weather. This spreader features a poly hopper with up to 109 kg (240 lb) of material-carrying capacity. After pairing with a Gator hitch and display (LP69908), spread-width adjustments can be made up to 7.6 m (25 ft) wide.

Benefits

• Enjoy long periods of spreading with the poly hopper that offers 109 kg (240 lb) of material capacity.
• Easily move large-particle material, like rock salt, to the spinner with the vertical auger.
  • NOTE: The spreader is not well suited to handle fine-particle materials like calcium chloride.
• The 25.4-cm (10-in.) diameter, nylon, glass-reinforced spinner withstands corrosive ice melt products for long-term use.
• Satisfy heavy-duty spreading demands with the 1/4-kW (1/3-hp), semi-sealed electric motor.
• Improve durability in rugged conditions with a powder-coated steel frame.

Additional details

The 0.085-m³ (3-cu ft) salt spreader is compatible with model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R Utility Vehicles.

To adapt this salt spreader to an XUV835 or XUV865 Utility Vehicle, the XUV835/XUV865 hitch and display (LP69908) is required.

Hitch and display for XUV835 and XUV865

Overview

The hitch and display for Gator XUV835 and XUV865 Full-Size Crossover Utility Vehicles are specifically designed to work with a 0.085-m³ (3-cu ft) salt spreader (LP69909), a 0.085-m³ (3-cu ft) fertilizer spreader (LP69910), or a 0.14-m³ (5-cu ft) drop spreader (LP69911).

Each hitch features a spring-loaded mechanism to allow for quick spreader attachment and removal. The hitch can also be lowered to provide easy access for routine service.

This latest generation of utility vehicles offer greater electronic capabilities than ever before. As a result, operators have access to enhanced functionality and controls, which is seen through the 9-cm (3.5-in.) weatherproof, color display.

Benefits

• Easily control the mounted spreader with the 9-cm (3.5-in.) weatherproof color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds and activating the vibratory motor on 0.14-m³ (5-cu ft) drop spreaders. The display mounts easily to the vehicle's dash by utilizing existing holes.
  • If a controller area network (CAN) bridge (BUC10316) is installed on the Gator, operators will also have access to automatic stop functionality, where spreader operation halts when the vehicle stops.
• Designed specifically for Gator utility vehicles, the hitch ensures safe and secure spreader fitment.
• The powder-coated steel hitch provides the utmost support and durability.

Additional details

The hitch and display are compatible with the following models:

• Model year 2018 and newer XUV835E, XUV835M, XUV835R, XUV865E, XUV865M, and XUV865R
• 0.085-m³ (3-cu ft) salt spreader (LP69909)
• 0.085-m³ (3-cu ft) fertilizer spreader (LP69910)
• 0.14-m³ (5-cu ft) drop spreader (LP69911)

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Side-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Side-door opening toolbox features:

• 125-L (4.4-cu ft) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Door can also be used as a work bench when down
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 – olive and black
• BM26219 – camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model year 2018 and newer HPX615 and HPX815

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Tailgate with brake lights and taillights

This tailgate kit with brake lights and taillights is specifically designed for compatibility with the top and side-door toolboxes (BM26162 and BM26160).

The tailgate can be installed in minutes once the toolbox and tail lights are installed by bolting them to the tailgate bracket.

Optional label kits are designed to fit with this tailgate:

• BM26220 – green and yellow
• BM26218 – olive and black
• BM26219 – camo

The tailgate is compatible with the following Gator™ utility vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model Year 2018 - current HPX615 and HPX815

Top-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Top door opening toolbox features:

• 125-L (33-gal.) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Toolbox divider
• Removable tool tray
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 –olive and black
• BM26219 – Camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model year 2018 and newer HPX615 and HPX815

Underhood storage tub and tray installed in vehicle

Underhood storage tub with removable tool tray

Key features

• Easily installs under the hood in models that do not have heating, ventilation, and air conditioning (HVAC) or the heater kit
• Storage tub has a volume of 21 L (5.5 gal.)
  • Rough dimensions: 88.1 cm x 20.3 cm x 38.2-cm deep (34.7 in. x 8 in. x 15-in. deep)
• Removable drain plug
• Removable tool tray
  • Dimensions: 45.5 cm x 19.3 cm x 4.6-cm deep (18 in. x 7.6 in. x 2-in. deep)

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles
  • Only compatible on these vehicles that do not have HVAC or heater kit installed

Tracks

Overview

Wheeled utility vehicles get buried very quickly in deep snow, swamps, sand, or muddy ground conditions. Adding a Camso tracks system takes you where wheels simply cannot go.

Benefits

• Improves flotation and traction
• All season capability – ideal for snow, mud, and marsh
• Easily switch between tracks and wheels

Additional details

• Compatible with model year 2021 and newer XUV835 and XUV865 Utility Vehicles

Camso is a trademark of Artic Investments S. A.

Front turn signals

Rear signal lights (taillight protectors not included)

Hazards switch (top)

Turn signal switch (right)

Key features

• Kit includes:

• Front/rear turn signals
• Hazards
• Backlit switches

NOTE: Not intended for use on public roadways.

Compatibility

• Compatible with all model year 2011 to current Gator™ XUV825 and XUV825 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Compatible with all model year 2011 to current Gator XUV625i, XUV855, and XUV855 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

• Effectively anchors to trees/boulders
• Change the pulling direction
• Double the pulling capacity

The accessories kit includes:

• Flexible tree strap
• Snatch block
• Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

Cordura is a trademark of INVISTA.

2041-kg (4500-lb) winch (chassis mounted)

Plug-in remote

Key features

• Impressive pulling capacity of 2041 kg (4500-lb)
• Equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities
• Includes a 3.05-m (10-ft), water-resistant, plug-in remote for safe distance operation that plugs directly into the glove box
• 15.2 m (50 ft) of 5.6-mm (7/32-in.) synthetic rope with hawse fairlead
  • Synthetic rope does not develop sharp burrs like steel rope and does not store as much potential energy when under load
• Ergonomic clutch handle
• Limited lifetime, 3-year electrical (North America) warranty offered through WARN

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• M-spec and R-spec vehicles come from the factory winch ready, and no additional attachment harnesses are required
• Requires winch mounting kit to mount the winch either on the chassis or on the front or rear receiver
• Not compatible with winch mounts BM26252 and BM26393

Electrical harness requirements

WARN is a trademark of WARN Industries, Inc.

Wireless winch remote

Wireless winch remote mounted on XUV835

Key features

• Wirelessly control winch from up to 15 m (50 ft) away
• Weatherproof transmitter has two large buttons, making it easy to operate even while wearing gloves
• Colored light-emitting diode (LED) lights provide clear operator feedback
• Kit includes wireless transmitter, receiver, holster, wiring, and mounting hardware

Compatibility

• Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

2041-kg (4500-lb) winch (chassis mounted)

Key features

• Kit includes everything needed to mount the winch to the chassis

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.

2041-kg (4500-lb) winch (chassis mounted)

2041-kg (4500-lb) winch (mounted on rear receiver)

Key features

• Ability to mount the winch on the front or rear receiver
• Kit includes everything needed to mount the winch to the receiver

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• Requires WARN VRX 2041-kg (4500-lb) winch (sold separately)

WARN is a trademark of WARN Industries, Inc.

Windshield washer bottle

Backlit three-position switch

Washer bottle location behind access panel

Key features

• Wash away dirt and debris with a quick flip of a switch
• Washer bottle conveniently located behind access panel
• Washer fluid comes out of nozzle on wiper arm (windshield wiper kit required)
• Kit includes washer bottle, hose connections, and three-position switch

Compatibility

• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements