XUV855M S4 (2021)Crossover Utility Vehicle

The Gator™ XUV Crossover Series Utility Vehicle has a precision-engineered drivetrain system that fully utilizes engine power, optimizing acceleration, hauling, towing, and hill-climbing capabilities. Power is transmitted from the engine through a continuously variable clutch system to the transaxle.

Key elements of the drive system include:

Variable-speed drive

Variable-speed drive

The variable-speed drive consists of two clutches and a drive belt:

• Drive clutch is attached to the engine.
• Driven clutch is attached to the transaxle.

Features include:

• The engine braking system utilizes a tight belt for operation, requiring an idler sleeve on the primary clutch for neutral. The secondary clutch is a new build-on-shaft design that utilizes a cam to tune the acceleration and deceleration of the vehicle. The clutch will stay engaged, providing deceleration until approximately 5 km/h (3 mph).
• The continuously variable transmission (CVT) air intake draws in cool air to reduce heat and the amount of water ingestion into the CVT system. The system will reduce belt slippage and improve durability.
• A low- and high-speed forward gear offering:
  • Low range is 0 km/h to 40 km/h (0 mph to 25 mph), XUV825E and XUV825M S4
  • Low range is 0 km/h to 24 km/h (0 mph to 15 mph), XUV855E and XUV855M S4
  • High range is 0 km/h to 72 km/h (0 mph to 45 mph), XUV825E and XUV825M S4
  • High range is 0 km/h to 45 km/h (0 mph to 28 mph), XUV855E and XUV855M S4
• Ability to creep along slowly to maneuver in tight spaces
• Standard full-clutch enclosure with high speed fan provides longer belt and clutch life
• High-ratio clutches with three cam weights for maximum belt clamp load in high-torque conditions
• Powertrain reduction ratios:
• The complete reduction ratios range for high gear is 8.6:1 at top speed and 42:1 at initial clutch engagement. This varies between the vehicles listed above.
• The complete reduction ratios range for low gear is 17.9:1 at top speed and 86.8:1 at initial clutch engagement. This varies between the vehicles listed above.

NOTE: Delivery of torque to the ground depends on tire size, which is a function of nominal size and pressure.

How the variable-speed drive works:

1. As engine speed increases, the spring-loaded drive clutch is closed by weights being forced out by centrifugal force.
2. As the drive clutch closes, the belt rides up to the largest diameter of the drive clutch and forces open the driven clutch.
3. With the belt running in the smallest diameter of the driven clutch, the speed being transferred to the transaxle is increased.
4. The driven clutch is designed to sense varying loads (inclines, mud, etc.) and constantly adjusts drive speed upward or downward so that engine rpm remains optimal.

Transaxle, mechanical front-wheel drive (MFWD), and constant-velocity (CV) shafts

Side view of CVT intake and clutch on closure (XUV855 shown)

Differential rocker switch

Rear end shot of transaxle/CV shafts

Operator interface

• Selectable four-wheel drive (4WD) system with a limited slip front differential and dash-mounted electronic rocker switch
• Provides exceptional traction in challenging conditions
• Maintains turf-friendly operation in two-wheel drive (2WD) mode
• Illuminated for visibility in low-light conditions

Transaxle features

• Low, high, neutral, reverse, and park transaxle
• Automotive-style, integrated park position in transmission
• Low range for maximum torque delivered to the wheels for hauling, pushing, and pulling
• High range for maximum vehicle speed
• To shift out of park, service brake must be pressed to release the parking solenoid. An audible click will be heard and allows the vehicle to shift out of park into the desired gear.

NOTE: Differential design reduces scuffing of the turf during turns because it allows the inside wheels to turn slower than the outside wheels

• Start in gear, neutral, or park position for quick starting. The service brake must be engaged to start when in gear or neutral.
• Large, sealed bearings are located inside the housing for better protection and durability
• Contains gear case for transferring power to the MFWD
• Splined shaft interfaces for maximum torque transfer and durability
• All drive gears machined from highest grade gear steel
• Protected by a skid plate

• Electronically selectable by the operator
  • Offers limited slip functionality for precision steering and great traction while pointing and shooting out of a corner
• Vertically oriented oil drain for easy maintenance
• Near instantaneous torque to the front wheels when electronic switch is engaged
• Protected by a steel skid plate and frame

Drive shafts

• Rear CV shaft diameter measures 27 mm (1.1 in.) and is designed for peak engine and braking torque
• Front CV shaft diameter measures 23.9 mm (0.94 in.) and is designed for peak engine torque
• Propshaft (transaxle to MFWD shaft) diameter measures 23 mm (0.91 in.) and is designed for peak engine torque
• All CV shaft and propshaft joints are maintenance free and protected by exclusive Neoprene boots for durability

XUV855 engine

Remote intake and restriction indicator

The machine is powered by an 854-cc (52.1-cu in.), 3-cylinder, liquid-cooled, four-cycle diesel engine. It produces 5.1 kgm (36.9 lb-ft) of torque at 2400 rpm.

The advanced engine delivers superb starting, idling, and throttle response during operation. With minimal noise vibration and harshness (NVH), the XUV855 is the smoothest and quietest running diesel in its class.

The engine offers the following performance and reliability features:

• Indirect injection diesel with glow plugs ensures fast starts in cold temperatures
• 30.6 kW (22.8 hp*) at 2400 rpm
• Overhead valve design for greater efficiency and fuel economy
• Spin-on oil filter for easy servicing
• Quiet operation through the entire rpm range
  • Molybdenum-coated pistons
  • High-stiffness cylinder block and gearcase
• High-flow water pump and optimized water jackets maintain a steady operating temperature and eliminate hot spots
• Full-pressure lubrication system
• In-line mechanical fuel pump
• Five-point, rubber isolated for quiet operation and minimal vibration
• Dry replaceable dual-element air cleaner with remote intake and a restriction indicator
• See-through coolant recovery tank permits the operator to check the coolant level without removing the radiator cap
  • Sealed radiator compartment keeps trash and debris on the outside of the grille

* The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. The actual operating horsepower will be less.

XUV front suspension detail

To complement the most capable frame available in a high-performance utility vehicle, the XUV is equipped with four-wheel independent suspension.

A dual A-arm front and rear suspension provides a smooth ride over challenging terrain and excellent hauling characteristics.

The entire suspension system has been optimized to handle no cargo to maximum cargo without compromising ride quality or vehicle stability.

Dual A-arm front suspension features include:

• 203.2 mm (8 in.) of travel provides ample compression and wheel extension, which keep all four wheels on the ground for superior traction and vehicle control
• 17.5-mm (0.6875-in.) solid anti-roll bar with fully rubber isolated connecting links and pivots for minimal vehicle body roll and quiet operation
• Heavy-duty, nodular cast-iron knuckles to support the strut, constant-velocity (CV) shaft, and wheel
• Maintenance-free rubber torsional A-arm pivots for long life and quiet operation
• CV shaft protection from sticks that may puncture the rubber boot

XUV rear suspension detail

Dual A-arm independent rear suspension features include:

• Unequal length, dual A-arm construction for superior wheel control and travel
• 228.6 mm (9 in.) of total travel provides ample compression and wheel extension, which keep all four wheels on the ground for superior traction, excellent ride quality, and vehicle control
• Coil-over shocks absorb the most demanding terrain
• A-arms made from square/rectangular tubing reduce weight while remaining rigid
• Heavy-duty, nodular cast-iron uprights support wheel loads with a double row of ball bearings
• CV driveshaft protection from sticks that may puncture the rubber boot
• Rear sway bar for lateral stability

Deluxe cargo box

The deluxe cargo box consists of a 15 percent glass-filled polypropylene composite material that eliminates rust, dents, and reduces noise.

Deluxe cargo box tailgate

Tailgate handle

Tailgate lowered to 150 degrees

The tailgate can be opened or removed for easier cleanout and to carry longer items. The tailgate has been improved, features truck-like performance, and can be operated with one hand.

The standard installed lanyards can also be removed to lower the tailgate to 150 degrees for convenient loading and unloading tasks.

Deluxe cargo box tilt

Integrated handle for manual cargo-box tilt

The deluxe cargo box is easier to latch, unlatch, raise, and lower with the integrated handle design and gas assist.

A prop rod is provided to hold the box in the upright position for operator convenience, as well as limit box pivot travel.

Integrated tie-down points

Integrated tie-down point in cargo box bed

Additional tie-down points (TH 6X4 shown)

The deluxe cargo box offers integrated tie-down points for increased versatility. Tie down points are located in the following areas:

• Four corners inside the cargo-box bed
• Four points on the load guard directly behind the operator station (A)
• Tie-down bars on either side of the cargo box (B)
• Six points on the underside of the cargo-box frame (circled)

Converting deluxe cargo box to a flat bed

Deluxe cargo box converted to flat bed (XUV825 shown)

The deluxe cargo box easily converts to a flat bed. The flatbed configuration allows loading larger cargo.

Optional accessories

Brake and taillight with optional protector

Bedmat—protects the steel floor from dents

Cargo box power lift

Optional accessories for the deluxe cargo box include:

• Factory-installed brake and taillight
• Factory-installed spray-in liner (not shown)
  • Improves skid resistance and surface abrasion protection
• Cargo box bed mat
• Cargo box power lift

Specifications

CAUTION: Carrying extra-long cargo that extends beyond the box can adversely affect stability.

This Gator™ XUV Crossover Utility Vehicle is equipped with power steering and a dual A-arm front suspension. These automotive-type systems exhibit excellent handling characteristics, as well as responsive steering and low steering effort:

• Steel ball bearings secure the steering shaft and deliver smooth, responsive operation
• Completely sealed rack-and-pinion for long life
• Low steering ratio (lock-to-lock) provides more responsive steering and less operator input
• Shaft U-joints are phased for a smooth, uninterrupted motion of the steering wheel

Electric power-assist steering system

Electric power-assist steering (EPAS) system has advanced features:

• Anti-kickback feature reduces the amount of steering unwinding when traversing difficult terrain.
• The system is speed sensing and adjusts steering effort as the speed of the vehicle changes.
  • As speed increases, there is less steering assist for improved road feel.
  • As speed decreases, steering assist increases to give lower steering efforts for improved maneuverability.
• A warning/functional light on the instrument panel provides self-diagnostics and a warning light in the situation of no assist.
• Torque sensor measures steering wheel input so the on-board computer can provide the appropriate output for various driving situations.

With the EPAS system, the operator maintains a direct, mechanical linkage from the steering wheel to the front wheels. The power-steering system interfaces mechanically with the steering system by being inserted between the steering wheel and the rack-and-pinion assembly.

A differential torque sensor is integrated into the power steering assembly. The circuit board assembly is also integral with the power-steering assembly.

Power steering does not reduce turning radius but significantly reduces steering effort by approximately 85 percent compared to those models without power steering.

EPAS interface diagram

EPAS interface diagram

The numbered descriptions refer to the EPAS interface diagram shown above:

1. Torque sensor
2. Engine control unit (ECU)
3. Fail-safe relay
4. Current/thermal control circuit
5. Reduction gears
6. DC motor
7. Rack and pinion
8. Function/warning light
9. Key power and ground
10. Vehicle speed sensor
11. Instrument cluster
12. Relay module

Seating for four

The XUV825M S4 and XUV855M S4 models feature seating for four. The rear seat will convert to provide a flat surface for extra payload and there is sealed under-seat rear storage for additional cargo.

Rear seat down

Storage for additional cargo under rear seat

StarFire™ 3000 Receiver and GreenStar™ (GS) installed on XUV 825i

GreenStar installed with tablet mount (sold separately)

The AMS integration kit allows the customer to mount their StarFire receiver and GreenStar display (both receiver and display sold separately) to their Gator Utility Vehicle.

Key features of the AMS integration kit:

• Compatible with StarFire iTC and 3000 receivers
• Compatible with GreenStar 2 1800, GreenStar 2 2600 and GreenStar 3 2630 displays
• GS display mounts to the occupant protective structure (OPS) for convenient access
• Ability to mount receiver to the poly roof, or on the OPS alone
• Switched power to receiver and display allows customer to run the AMS equipment even when the vehicle’s ignition is off.  Receiver and display will not turn off when the vehicle’s ignition is turned on and off.
   

Common applications:

• Boundary mapping
• Flagging field obstacles
• Soil sampling
   

Compatibility:

• Model year 2011 to current HPX, XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles
• If installed on the poly roof, compatible with poly roofs on Model Year 2013 to current Utility Vehicles
• Compatible with full windshield, poly cab
• Not compatible with deluxe cab

POWERtach rubber squeegee

Rubber squeegee

• Absorbs impacts and conforms to the surface being plowed
• Is a great choice for use on sidewalks and other sensitive surfaces such as brick and cobblestone
• Provides quiet operation ideal for residential and commercial applications

Ordering information

Contact your local John Deere dealer for availability and pricing information.

POWERtach rubber squeegee
Order number: LPPK150

POWERtach is a U.S.-registered trademark of POWERtach company.

Shown on XUV825i

The operator protection system (OPS) poly rear window is an excellent solution for operators seeking to reduce dust and air flow throughout the operator station when coupled with a half or full windshield (vent open for best results). Made out of high-impact-strength abrasion-resistant polycarbonate material, this rear window is highly durable and scratch resistant. It also attaches to and detaches from the OPS with ease, thanks to the quick-clamp mounting system.

Compatible with Gator™ XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and HPX Utility Vehicles.

Poly cab seal kit

Improve the OPS Poly Cab seal on the Gator™ Utility Vehicle with the addition of the seal kit which installs around the doors, windshield, roof, and cab frame.

Compatible with OPS Poly Cabs installed on 4 passenger XUV825i/E/M and XUV855D/E/M Gator™ Utility Vehicles.

OPS rear panel (shown with poly roof)

The rear panel for the OPS poly cab is ideal for outdoor enthusiasts and others desiring four-season weather protection.

The Poly Cab is sold as individual components; OPS poly or glass windshield, OPS poly roof, OPS rear panel, and doors kit. This gives operators the flexibility to configure the vehicle to meet their unique needs.

Key features of the rear panel:

• Rear panel is thermoformed from thick ABS plastic for impact resistance, durability, and style
• Three-piece sliding glass window, which provides excellent visibility and ventilation
• Installs in minutes with quick clamps to the OPS structure
• Installed with full windshield (vent open) to help eliminate dust from entering operator station

Compatible with:

• MY13-current HPX (if equipped with cargo box power lift)
• MY13-current 625i
• MY13-current 825i and 825i S4
• MY13-current 855D and 855D S4

Poly cab doors (shown with rear panel, poly roof, and glass windshield)

Poly cab doors (shown with glass windshield, poly roof, and rear panel)

The poly cab doors for the operator protection system (OPS) poly cab is ideal for outdoor enthusiasts. Doors are not sealed for water tight performance.

The poly cab is sold as individual components; OPS poly or glass windshield with wiper, OPS poly roof, OPS rear panel, and the doors kit. This gives operators the flexibility to configure the vehicle to meet their unique needs.

Key features of the poly cab doors:

• Doors are thermoformed from thick acrylonitrile butadiene styrene plastic for impact resistance, durability, and style
• Reinforced with steel tubing for rigidity
• Mounted on heavy-duty hinges for durability
• Automotive style latches
• Locking door handles
• Large glass sliding windows provide excellent side-to-side visibility
• Standard side rear-view mirrors on the driver and passenger front doors
• Integrated seals to improve the operator enclosure

Optional accessories designed to integrate with the OPS poly cab system:

• Cab heater
• Heavy-duty POWERtach™ 72-in. blade
• OPS and roof mounted lights
• OPS seat belt comfort strap
• OPS overhead organizer
• Floor mats
• Beacon light

Compatible with:

• Model year 2013 - current Gator™ XUV 825i/E/M S4 and XUV 855D/E/M S4 Utility Vehicles

Cargo box pail holder

Cargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Cargo bed extender

Cargo bed extender

The cargo bed extender conveniently extends the rear of the cargo bed, and also acts as a cargo box divider when it is flipped inside of the cargo box. The cargo bed extender easily flips in or out with the use of quick-pull pins.

Deluxe cargo box bed mat

The deluxe cargo box bed mat not only protects the steel floor from scratches and dents, it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box divider located at rear of cargo bed

Cargo box divider located at front of cargo bed

Speedrail lock in the unlocked position

Speedrail lock in the locked position

The Gator™ XUV Series can be equipped with an optional divider for the deluxe cargo box. The dividers can be positioned at the front or rear of the cargo box bed. To change positions of the dividers, simply release the speedrail locks by hand and slide into new position, then close the locks to secure the dividers.

Cargo box side extension kit

The cargo box side extension kit expands the versatility of the Gator™ Utility Vehicles and is ideal for those who are enhancing their property and landscape. The extensions allow operators to haul twice the volume (not to exceed cargo box weight capacity) of light material such as grass clippings and mulch. 

Product features include:

• Four-sided structure that increases cargo box side height to 533 mm (21 in.) and volume to 0.74 m³ (26 cu ft)
• Mounted on the sides and front with hardware, while the tailgate can be attached or removed without tools
  • Tailgate pivots at the top (similar to a dump truck) for ease of dumping loose material
• Laser-cut, heavy-gauge, powdered-coated steel provides excellent durability
• Compatible with all model year 2011 to current Gator XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, and M-Gator A2 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles.
• Compatible with Gator cabs and bedliner

NOTE: The cargo box side extensions are not intended to increase the rated cargo box carrying capacity per the vehicle specification.

Sportsman case for Gator utility vehicles

Overview

This sportsman case from Black Mountain All-Terrain is a great storage upgrade to the bed of all Gator XUV Full-Size Utility Vehicles including XUV835, XUV865, XUV625, XUV825, XUV825 S4, XUV855, and XUV855 S4 models, as well as the Work Series Utility Vehicles including HPX615E, HPX815E, TE, TH, and TX models.

Benefits

• Functions as a toolbox and/or a hunting equipment storage case
• Secures and removes quickly from bed of a Gator utility vehicle or personal vehicle
• Keeps valuable items protected inside durable, protective plastic insert with foam padding and heavy fabric exterior
• Transports easily with shoulder strap and carry handles
• Customizable with two color choices: 
  • Realtree EDGE® camo with black base
  • Classic black

Additional details

• Holds two hunting accessories/instruments up to 127-cm (50-in.) in length
• Case easily attaches and detaches to cargo box with four quick-connect buckles
• Four D-rings with removable straps for easy removal from the XUV or pickup truck
• Convenient hand carry straps on top and grab handles on each end
• Made from water-resistant, mildew-resistant, and abrasion-resistant material
• Base covered with durable ballistic nylon/poly fabric that is resistant to tearing
• Oversized, corrosion-resistant zippers for durability and ease of use
• Lockable zippers allow contents to remain secure
• Top-loading design with wide opening lid allows quick access
• Acrylonitrile butadiene styrene (ABS) plastic interior frame protects valuable contents

The case is 127-cm (50-in.) long, 22.9-cm (9-in.) wide, 38.1-cm (15-in.) high, and weighs 7.7 kg (17 lb).

Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Sportsman case for Gator utility vehicles

Overview

This sportsman case from Black Mountain All-Terrain is a great storage upgrade to the bed of all Gator XUV Full-Size Utility Vehicles including XUV835, XUV865, XUV625, XUV825, XUV825 S4, XUV855, and XUV855 S4 models, as well as the Work Series Utility Vehicles including HPX615E, HPX815E, TE, TH, and TX models.

Benefits

• Functions as a toolbox and/or a hunting equipment storage case
• Secures and removes quickly from bed of a Gator utility vehicle or personal vehicle
• Keeps valuable items protected inside durable, protective plastic insert with foam padding and heavy fabric exterior
• Transports easily with shoulder strap and carry handles
• Customizable with two color choices: 
  • Realtree EDGE® camo with black base
  • Classic black

Additional details

• Holds two hunting accessories/instruments up to 127-cm (50-in.) in length
• Case easily attaches and detaches to cargo box with four quick-connect buckles
• Four D-rings with removable straps for easy removal from the XUV or pickup truck
• Convenient hand carry straps on top and grab handles on each end
• Made from water-resistant, mildew-resistant, and abrasion-resistant material
• Base covered with durable ballistic nylon/poly fabric that is resistant to tearing
• Oversized, corrosion-resistant zippers for durability and ease of use
• Lockable zippers allow contents to remain secure
• Top-loading design with wide opening lid allows quick access
• Acrylonitrile butadiene styrene (ABS) plastic interior frame protects valuable contents

The case is 127-cm (50-in.) long, 22.9-cm (9-in.) wide, 38.1-cm (15-in.) high, and weighs 7.7 kg (17 lb).

Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Rear fender flare kit on XUV865

Rear fender flare kit

A – Fender flare

B – Fender

The rear fender flare kit minimizes debris from reaching the operator station.

Product features include:

• Two pliable fender flares (one for each side)
• Hardware for mounting on the sides
• Compatible with all model year 2011 to current Gator™ XUV825, XUV825 S4, XUV855, XUV855 S4, XUV835, and XUV865 Utility Vehicles
• Compatible with model year 2010 to current Gator TX 4X2, TH 6X4 Gas, TH 6X4 Diesel, TE, and TX Turf Utility Vehicles
• Compatible with model year 2018 and newer gas and diesel HPX Utility Vehicles

Tool rack

Tool rack with tools

The side tool rack enables the user to maximize the use of their cargo box by carrying long-handled tools, such as trimmers, shovels, and rakes, on the outside of the box. The holders are adjustable, allowing the users to carry a wide array of items in the racks.

Tool rack holder detail

Adjusting the tool rack holder

Spare tire carrier

Spare tire carrier

Easily mount a spare tire to the side of the cargo box with this convenient kit.

Recommended to carry spare front tire, as the front tire can be mounted on either the front or rear hubs.

Cargo box power lift kit shown in full up position

Overview

The Gator™ utility vehicles can be equipped with an optional power lift for the cargo box. This is one of the most important accessories for increasing work efficiency. It is an excellent complement to these highly capable utility vehicles.

Benefits

• Capable of lifting a maximum vehicle cargo box load of 454 kg (1000 lb)
• Lifts box to 49 degrees from horizontal for ease of service and cargo box load removal
• Quick horizontal-to-49-degree time
• Can be installed in minutes using the vehicle's prewired connectors and mounting points
• Compact design fits nicely around the transmission and linkages, providing full protection
• Fully sealed and weatherproof design does not require maintenance and is built for maximum durability
• Overload protection protects against misuse

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Engine coolant heater

Adapter parts

Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts. It is rated for 400 W output power.

Yellow bench seat cover

Gator™ HD XUV bench seat cover

• Designed for heavy-duty two-passenger and four-passenger Gator XUV Utility Vehicles
• Compatible with Gator XUV625, XUV825, XUV855, XUV825 four-passenger, and XUV855 four-passenger Utility Vehicles
• Includes cover for seat and back benches
• Must order two kits for four-passenger (two-row) vehicles
• Protection for bench seats from mud and stains
• Cushioned seat for extra comfort
• Convenient pockets to store tools and gear
• Elastic hem-cord closure for easy adjustment resulting in a custom-like fit
• Easy access to seatbelts
• Options for storing gear behind the seats with zippered and open-top pouches

Ordering information
Contact the local John Deere dealer for availability and pricing information.

Drawbar kit for receiver hitch

Description:

• Kit includes a 51-mm (2-in.) drawbar, 10-mm (0.39-in.) pin, and hair cotter pin
• Steel construction has a 25-mm (1-in.) ball hole size
• Can be mounted in the standard rear receiver hitch or the optional front receiver hitch
• Compatible with all Gator model year 2011-current XUV560, XUV560 S4, XUV590, XUV590 S4, XUV 625i, XUV 825, XUV 855, RSX860, and M-Gator™ A2 Utility Vehicles
• Compatible with HPX 615 and 815 Utility Vehicles
• Compatible with XUV 620i and XUV 850D Utility Vehicles

NOTE: Compatible with all Gator HPX Utility Vehicles if equipped with an optional 51-mm (2-in.) front receiver hitch. An optional 51-mm (2-in.) rear receiver is not available for the Gator HPX models. A 32-mm (1-1/4-in.) rear receiver hitch and drawbar are available for the Gator HPX models.

Floor mat (shown on XUV 825i)

The washable rubber mat protects the vehicle floor.

Compatible with Gator HPX, XUV 625i, XUV 825i, XUV 825i S4, XUV 855D, XUV 855D S4, M-Gator™ A2 Military, and M-Gator A3 Military Utility Vehicles. 

Floor mats (shown on XUV 825i S4)

The removable and washable rubber floor mats provide an added layer of protection to the floor of the vehicle, and guards against dents, dings, and scratches.

Compatible with model year 2013-current XUV 825i S4 and XUV 855D S4 Utility Vehicles.

Front hood rack

Expand the work capabilities of a Gator™ Utility Vehicle with the addition of the front hood rack designed specifically for all model year 2011 Gator XUV625i, XUV825i, XUV855D, and M-Gator A2 Utility Vehicles. This generously sized rack (121.9-cm [48 in.] long x 34.3-cm [13.5 in.] wide x 8.9-cm [3.5 in.] deep) will haul up to a 45.4-kg (100-lb) payload.

It is also compatible with model year 2013-current Gator XUV825i S4 and 855D S4 Utility Vehicles, and model year 2018-current gas and diesel HPX Utility Vehicles.

The rack easily mounts to the required BM22841 front brush guard. Once mounted, the rack tilts forward with the brush guard to allow full access to under-hood storage and service points.

The front hood rack is compatible with the occupant protective structure (OPS), OPS poly windshields, and deluxe cab system. The front windshield will open to the vent position, but it will not open all the way unless the front hood rack is swung forward.

Cargo box fender guard kit

The cargo box fender guards offer enhanced styling in addition to heavy-duty protection to the side of the cargo box:

• Compatible with all model year 2011 and later Gator™ XUV 625i, XUV 825i, and XUV 855D Utility Vehicles.
• Compatible with model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles.
• Compatible with model year 2010 and later Gator TX, TX Turf, and TE Utility Vehicles.

NOTE: BM22767 rear bumper is required to install the cargo box fender guards.

Deflector plate detail

The large, heavy-duty skid plate adds additional protection for the frame and critical powertrain components:

• Thick, 3.8-mm (0.15-in.) material handles impacts
• Compatible with model year 2011 and later Gator™ XUV 855D Utility Vehicles
• Compatible with model year 2013 - current Gator XUV 855D S4 Utility Vehicles

Front CV guards

CV guards add additional protection for the A-arms and CV half shafts:

• Formed steel guards handle impacts while maintaining a low, unsprung mass
• Easily bolts to the A-arms
• Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
• Compatible with all Gator™ XUV625, XUV825, XUV825 S4, XUV855, XUV855 S4, and M-Gator A3 Utility Vehicles

Heavy-duty fender guard (shown on XUV825i)

The heavy-duty fender guards provide a modern and aggressive appearance for all model year 2011-current Gator™ XUV625i, XUV825i, XUV855D, and M-Gator A2 Utility Vehicles.

It is also compatible with model year 2013-current Gator XUV825i S4 and 855D S4, and model year 2018-current gas and diesel HPX Utility Vehicles.

• Large, 1.75-in. (44.45-mm) diameter tubing provides superb protection for the front grille, lights, and fenders
• Compatible with standard front bumper

Brush guard shown on XUV855D Olive and Black

Brush guard shown on XUV625i Camo

NOTE: Images above show brush guard with Adventure light kit installed.

The heavy-duty brush guard provides a modern and aggressive appearance for all model year 2011 to current Gator™ XUV625i, XUV825i, XUV855D, and M-Gator A2 Utility Vehicles. It is compatible with model year 2018-current gas and diesel HPX Utility Vehicles.

• Massive welded brush guard is made of large-diameter, 44.45-mm (1.75-in.) tubing and thick steel plates to provide superb protection for the front grille, lights, and hood
• Possesses welded brackets for quick installation of the Adventure light kit
• Rotates forward without tools for easy access to service points and additional storage under the hood

Rear bumper kit (TH 6X4 shown)

The rear bumper offers stylish, heavy-duty rear protection to the vehicle.

Compatible with:

• Model year 2011 and later Gator™ XUV 625i, XUV 825, and XUV 855 Utility Vehicles
• Model year 2010 and later Gator TX, TX Turf, TH 6X4 Gas, TH 6X4 Diesel, and TE Utility Vehicles
• Model year 2018 and later Gator XUV835 and XUV865 Utility Vehicles

Rear CV guards

CV guards add additional protection for the A-arms, brake lines, and CV half shafts:

• Formed steel guards handle impacts while maintaining a low unsprung mass
• Easily bolt to the A-arms with six bolts
• Drainage holes provided to prevent buildup of dirt, grass, and other loose materials
• Compatible with all model year 2011 to current Gator™ XUV625i, XUV825, XUV855, and M-Gator A2 Utility Vehicles
• Compatible with model year 2013 to current Gator XUV825 S4 and XUV855 S4 Utility Vehicles
• Compatible with model year 2018 to current Gator XUV835 and XUV865 Utility Vehicles

Brake and taillight protector

The brake and taillight protector offers increased protection to the taillight assembly from incidental contact.

Beacon light harness kit (shown on Gator™ XUV560 S4)

The beacon light harness kit is required when installing the beacon light.

The kit includes the switch to mount in the operator protection system (OPS) switch bank and wire harness between the OPS switch bank and beacon light.

Brush guard light harness kit

The brush guard light harness kit is required when installing the light kits to the brush guard on Gator™ utility vehicles.

The kit includes the switches and wire harnesses.

Front OPS / roof light harness kit

The front OPS/roof light harness kit is required when installing the light kits to the front of the OPS or roof. Also requires OPS switch bank.

The kit includes the switch and wire harnesses from the OPS switch bank to the lights.

Turn signal light harness kit

The turn signal light harness kit is required when installing the turn signal light kit.

The kit includes the switches and wire harnesses.

Compatible with Gator™ HPX, XUV560, XUV550, XUV590i, XUV590i S4, XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles.

Heater kit

Three directional louvers provide windshield defrosting and complete operator comfort.

Kit includes:

• High-output two-speed heater
• Mounting hardware
• Coolant hoses
• Electrical harness 

Heater outputs around 9800 BTU

Compatible with the following vehicles:

• All model year 2011 - current Gator™ HPX Gas, HPX Diesel, XUV 625i, XUV 825i, XUV 855D, and M-Gator A2 Utility Vehicles
• Also compatible with model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles

Kit includes:

• Hoses and conduit to allow cab heater kit to work on XUV 825i and 855D S4 Utility Vehicles.

Compatible with:

• XUV 825i S4 and 855D S4 Utility Vehicles

Heater fitting kit

It is compatible with the following vehicles:

• All model year 2011 - current Gator™ XUV 855D and M-Gator™ A2 Utility Vehicles
  • This heater fitting kit works with BM23608 heater kit and diesel engine
• All model year 2004 - current Gator HPX and XUV 850D Utility Vehicles
  • This heater fitting kit works with BM23608 heater kit and diesel engine
• All model year 2013 - current Gator XUV 855D S4 Utility Vehicles
  • This heater fitting kit works with BM23608 heater kit and diesel engine

Horn components

Kit includes:

• Horn
• Mounting brackets
• Wire harness and switch

The switch mounts on the dash of the vehicle, while the wiring harness connects to the main vehicle harness.

Beacon light

Features and benefits:

• 3-in. (76-mm) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
• Especially useful for working around properties and job sites
• Acrylic amber lens resists scratching and scuffing
• Impact-resistant nylon housing
• SAE J845 (Class 3)-compliant
• UL recognized
• Stands 4.4 in. (111.5 mm) tall

Compatible with the following vehicles:

• Model year 2006 to current Gator™ HPX Utility Vehicles
• Requires poly roof and operator protection system (OPS) switch bank for mounting
• Requires beacon light harness kit
• Gator XUV 620i and 850D Utility Vehicles
• Requires poly roof and OPS switch bank for mounting
• Requires beacon light harness kit
• Model year 2011 to current Gator XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles
• Requires poly roof and OPS switch bank for mounting
• Requires beacon light harness kit
• Gator XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590i, XUV590i S4 Utility Vehicles
• Requires OPS switch bank and brake/tail light for brake light mounting or OPS switch bank and poly roof for roof mounting
• Requires beacon light harness kit
• Gator RSX Utility Vehicles
• Requires OPS switch bank and brake/taillight for brake light mounting or OPS switch bank and poly roof for roof mounting
• Requires beacon light harness kit

Brake and taillight kit

The integrated brake and taillight kit offers an updated stylish design in addition to being highly visible in all light conditions.

NOTE: For model year 2018 and newer HPX615 and HPX815 Utility Vehicles, the reverse lights will not illuminate.

Compatible with:

• Model year 2017 – newer Gator™  XUV 825i, XUV 825i S4, XUV 855D, and XUV 855D S4 Utility Vehicles
• Model year 2018 – newer Gator HPX615 and HPX815 Utility Vehicles

OPS with power wire and switch bank

Switch bank (detail)

Product attributes:

• Accommodates up to three sets of OPS lights
• Allows for simple wire routing - only two wires run through the OPS or roll-over protective structure (ROPS) tubes; each light kit has its own switch and wiring harness
• Switches are located in the OPS or rollover protective structure (ROPS)

Compatible with:

• Model year 2011 - current Gator™ XUV, HPX Gas, HPX Diesel, and M-Gator A2 Non-Military Utility Vehicles
• Model year 2012-2013 Gator XUV 550, XUV 550 S4, and RSX Utility Vehicles
• Model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles
• Current Gator XUV560, XUV560 S4, XUV590, and XUV590 S4 Utility Vehicles

Rear OPS / roof light harness kit

The rear OPS/roof light harness kit is required when installing the light kits to the rear of the OPS or roof on the Gator™ S4 Vehicles. Also requires OPS switch bank.

The kit includes the switch and wire harnesses from the OPS switch bank to the lights.

Work lights (rear mounted)

Increase the capability of the Gator™ Utility Vehicle by adding work lights. Lights mount to the front or rear of the poly roof or directly to the operator protection system (OPS).

Kit includes the pair of work lights and hardware. Requires necessary light harness kit based on desired mounting location.

Lights can also be installed in a low mount position behind the front bumper.

Product attributes:

• This flood light kit provides a wide range of light, making it ideal for tasks at night
• Especially useful for working around properties and job sites
• Requires OPS switch bank when mounted to roof or OPS

Compatible with:

• XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590i, XUV590i S4
• HPX
• XUV 625i, XUV 825i, XUV 825i S4, XUV 855D, and XUV 855D S4
• RSX Utility Vehicles

Shown mid-size XUV

The OPS rearview mirror for Gator™ Utility Vehicles can be installed when equipped with an OPS.

The rearview mirror can be positioned in multiple locations on the OPS and offers expanded visibility for the operator.

Product attributes include:

• Composite components made of impact resistance materials
• Installs with quick clamp to OPS tube
• Compatibility with all Gator Utility Vehicles equipped with an OPS

Shown on Gator™ HD XUV

Shown on HD XUV

The OPS side mirrors for Gator Utility Vehicles can be installed when they are equipped with OPS.

The side mirrors can be positioned in multiple locations on the OPS and offers expanded visibility for the operator.

Product attributes include:

• Composite components made of impact-resistant materials
• Installs without tools and easily adjustable
• Compatibility with all Gator HPX, XUV 620i, XUV 850D, XUV 625i, XUV 825i, XUV 825i S4, XUV 855D, XUV 855D S4, XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, RSX, M-Gator A2, and M-Gator A3 Utility Vehicles equipped with an OPS

NOTE: OPS side mirrors are not compatible with the deluxe cab or poly cabs (poly cabs include standard mirrors).

OSR door with green panel

OSR door with olive panel

OSR door with camo panel

The OSR door kits are replacement kits for the factory-installed OSR doors, or can be installed on vehicles that had the OSR nets installed from the factory. These OSR doors can only be installed on model year 2014 or later Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles.

The OSR color panels are sold separately, and can be installed on the OSR doors or the deluxe poly door.

OSR door with green panel

OSR door with olive panel

OSR door with camo panel

The OSR door kits are replacement kits for the factory-installed OSR doors, or can be installed on vehicles that had the OSR nets installed from the factory. These OSR doors can only be installed on model year 2014 or later Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles.

The OSR color panels are sold separately, and can be installed on the OSR doors or the deluxe poly door.

OPS stereo mounting kit shown with head unit

OPS stereo mounting kit - head unit/iPod player

Features include:

• Convenient netted storage area to store items such as, sunglasses, CDs, maps, and other personal items
• Two pre-mounted speakers
• Two interior lights; each light can be independently operated
• A 3-switch bank to operate various roof and OPS mounted accessories

Compatible with:

• Model year 2013 - current Gator™ XUV 825i S4 and 855D S4 Utility Vehicles also equipped with a poly roof

NOTE: Not compatible with deluxe cab frames.

The OPS stereo mounting kit includes the mounting kit only; the customer must choose one of the following three-head units to have a complete stereo:

• SWJHD1120 stereo, heavy-duty AM/FM/weatherband/auxiliary
• SWJHD1620 stereo, heavy-duty AM/FM/weatherband/SIRIUS® Satellite/iPod® ready
• SWJHD3620 stereo, heavy-duty AM/FM/weatherband/CD/SIRIUS Satellite/USB 2.0
• SWJDABIPDL iPod adaptor cable for SWJHD1620 and SWJHD3620

SIRIUS is a U.S.-registered trademark of SIRIUS XM Radio Inc. iPod is a U.S.-registered trademark of Apple Incorporated.

SWJHD1120 stereo head unit

SWJHD1620 stereo head unit

SWJHD3620 stereo head unit

OPS soft roof – shown in black

• Provides year-round weather protection to the operator and passenger when a Gator™ XUV 825i S4 Utility Vehicle or 855D S4 Utility Vehicle is equipped with an OPS or rollover protective structure (ROPS)
• Useful for minimizing sun exposure to the operator, passenger, and vehicle operating station
• One-piece, soft roof allows for tool-free attachment/detachment to the OPS or ROPS with four simple adjustable straps
• Heavy-weight polyester fabric for maximum durability and resistance to tear
• PVC coating provides for superior water resistance and repellency
• Compatible with the OPS rear screen, OPS poly windshields, and OPS organizer
• Compatible with the Gator XUV 825i S4 and 855D S4 Utility Vehicles

NOTE: Must be removed for transport on an open trailer or truck.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

OPS soft roof - camo

• Provides year-round weather protection to the operator and passenger when a Gator™ XUV 825i S4 or 855D S4 is equipped with an OPS or rollover protective structure (ROPS)
• Useful for minimizing sun exposure to the operator, passenger, and vehicle operating station
• One-piece, soft roof allows for tool-free attachment/detachment to the OPS or ROPS with four simple adjustable straps
• Heavyweight polyester fabric for maximum durability and resistance to tear
• PVC coating provides for superior water resistance and repellency
• Compatible with the OPS rear screen, OPS poly windshields, and OPS organizer
• Compatible with the Gator XUV 825i S4 and 855D S4 Utility Vehicles

NOTE: Must be removed for transport on an open trailer or truck.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Side view of black OPS poly roof

Rear view of black OPS poly roof

Features of the OPS poly roof include:

• Provides all-year-round weather protection to the operator and passenger when a Gator™ XUV is equipped with an operator protection system (OPS)
• One-piece ABS roof easily attaches/detaches to the OPS quick-clamp mounting system
• Useful for minimizing sun exposure to the operator, passenger, and vehicle operating station
• Molded-in water troughs route water away from the operator and passenger
• Acts as the foundation to build an OPS poly full enclosure (designed to work with the OPS poly full windshield kit and OPS poly rear panel and doors kit)
• Compatible with all model year 2013 – current XUV 825i/E/M S4 and XUV 855D/E/M S4 Utility Vehicles when equipped with an OPS

Cushioned covers protect new seats and renew old seats

Features:

• Heavy-duty seat protection against sun damage, rain, and dirt
• Cushioned for extra comfort
• Elastic cord hem for a custom fit
• Two convenient zippered pockets keep tools and gear within reach 
• Two mesh stuff pockets
• Two-year warranty

Ordering information
Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

Front bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special features:

• Exceptional abrasion, tear, and puncture resistant
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Also available in REALTREE HARDWOODS HD™ pattern
• Front seat has modular lightweight load-carrying equipment MOLLE webbing between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Front bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special features:

• Exceptional abrasion, tear and puncture resistance
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Also available in black
• Front seat has modular lightweight load-carrying equipment (MOLLE) webbing between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics.

Front bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special Features:

• Exceptional abrasion, tear, and puncture resistant
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in REALTREE HARDWOODS HD™ pattern
• Front seat has MOLLE webbing between driver and passenger and back panel for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Front bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special features:

• Exceptional abrasion, tear, and puncture resistant
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Also available in black
• Front seat has MOLLE webbing between driver and passenger and back panel for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics.

Rear bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special features:

• Exceptional abrasion, tear, and puncture resistant
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in REALTREE HARDWOODS HD™ pattern
• Back rest has modular lightweight load-carrying equipment (MOLLE) system between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Rear bench seat cover

Available through OrderZone

Each kit contains: one bench base cover, one backrest cover, and installation instructions

Special features:

• Exceptional abrasion, tear, and puncture resistant
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in REALTREE HARDWOODS HD™ pattern
• Back rest has modular lightweight load-carrying equipment (MOLLE) system between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Comfort straps

Kit includes two comfort straps for the left and right seat belts.

• Provides relief to the operator's and passenger's upper body when driving over rough terrain by allowing the seat belt to stretch when the seat belt locks
• Moves the upper mounting point of the seat belt down 6 in. (152 mm)
• Can be mounted to both the driver- and passenger-side upper mounting point of the three-point seat belt
• Compatible with all model year 2017 - current Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, and RSX860i Utility Vehicles when equipped with standard Occupant Protective Structure (OPS)
• Compatible only with standard Occupant Protective Structure (OPS), for deluxe cab frame, order BM22703

Comfort straps

A seat belt comfort strap is available for Gator™ Utility Vehicles equipped with an Occupant Protective Structure (OPS) or roll-over protective structure (ROPS).

Product attributes

• Kit includes two comfort straps for the left and right seat belts
• Provides relief to the operator's and passenger's upper body when driving over rough terrain by allowing the seat belt to stretch when the seat belt locks
• Moves the upper mounting point of the seat belt down 6 in. (152 mm).
• Can be mounted to both the driver- and passenger-side upper mounting point of the three-point seat belt
• Compatible with XUV620i and XUV850D Utility Vehicles
• Compatible with Model Year 2015 and older Gator HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4 and Military A3 Utility Vehicles
• Compatible with Model Year 2016 to current Gator HPX, XUV625i, XUV825i and XUV855D Utility Vehicles equipped with a Deluxe Cab
• Compatible with Model Year 2015 and older Gator XUV550, XUV550 S4, and RSX Utility Vehicles

45-gal. (170-L) Gator bed sprayer

The 45-gal. (170-L) Gator bed sprayer is designed to work with the Gator vehicles equipped with the steel bed or deluxe cargo box. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 43-in. boom that sprays a 120-in. swath. It's equipped with a 20-ft hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft. It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no tools mount.

Special features:

• 45-gal. (170-L) capacity
• Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
• Brackets allow boom height adjustment
• 100 psi SHURflo diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
• The fully adjustable brass spray wand tip achieves streams up to 30 ft
• Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• On/off switch located near operator
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• 12-V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

45-gal. (170-L) Gator bed sprayer
Order number: LP20852

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

High-performance 45-gal. (170-L) Gator bed sprayer

The high-performance Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box or steel bed. With a 45-gal. (170-L) capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and de-icer. Engineered brackets secure the sprayer to the Gator bed with no tools, or additional tie-downs required.

NOTE: Sprayer shown above with optional 150-in. precision boom (LP22885).

High-performance features:

• 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single hand mist to 35-ft stream
• Equipped with a 20-ft hand wand hose with side mount hose tender for convenience
• Glycerin-filled pressure gauge and TeeJet™ pressure regulation/recirculation valve
• Choice of booms (sold separately)
• On/off capabilities in the palm of your hand with the included sprayer remote control (LP22912)
• 12V plug included with wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Brackets secure to Gator bed, no tools or additional strapping required after initial set-up
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

High-performance 45-gal. (170-L) Gator bed sprayer
Order number: LP22908

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

25-gal. (95-L) Gator bed sprayer

The improved 25-gal. (95-L) Gator bed sprayer is designed to work with all steel bed and deluxe cargo box Gator Utility Vehicles (except CX), and provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 109-cm (43-in.) boom that sprays a 304.8 cm (120-in.) swath. It is equipped with a 5.8-m (19-ft) hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 9.1 m (30 ft). Engineered brackets secure the unit to Gator bed with no tools or additional strapping required.

Features include:

• Brackets secure to the Gator bed with no additional strapping or bungees required
• Brackets allow boom height adjustment
• 100 psi Shurflo® diaphragm-type pump is designed for high hour commercial applications - it can be run dry without damage
• The fully adjustable brass spray wand tip achieves streams up to 9.1 m (30 ft)
• Equipped with a 5.8-m (19-ft) hand wand hose
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• On/off switch located near operator, 12-V plug included complete with quick-disconnects, for convenient electrical hookup
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

25-gal. (95-L) Gator bed sprayer
Order number: LP33597

SHURflo is a U.S.-registered trademark of Sta-Rite Industries, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

25-gal. (94 L) portable sprayer

The 25-gal. (94 L) portable sprayer is ideal for caring for shrubs, decorative trees, and fruit trees.

• Four rubber feet bolted to the bottom of the tank protect and stabilize it when placed in a cart, Gator™, or other vehicle for transporting
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30 ft in height
• Handgun comes with a 19-ft hose and a handgun with 14-in. wand

Additional features include:

• 100 psi, 2.1 gpm diaphragm-type pump designed for high-hour commercial applications; it can be run dry without damage
• Spray wand is constructed of non-corrosive polypropylene material with Viton® components for remote spray jobs
• Two-wire fused wiring harness complete with quick-disconnects for convenient electrical hookup
• Large cap to easily fill up the tank
• Rugged translucent yellow tank with molded fill-level indicators (in gallons)

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

These liquid sprayers are especially suited for maintaining residential and small commercial properties:

• Provide an excellent way to apply liquid fertilizer
• Herbicides and pesticides can be applied along with liquid fertilizer or separately

Following are the advantages of using liquid fertilizer over dry fertilizer:

• More readily available to plants
• Need not be worked into the soil by watering or rain before it will work
• Herbicides are more effective when applied with liquid fertilizer

NOTE: Use these sprayers with liquid-base lawn care chemicals only. Not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Compatible with all Gator models except XUV 550, XUV 550 S4, and RSX850i Utility Vehicles.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

25-gal. (94 L) portable sprayer
Order number: LP19490

170-L (45-gal.) Gator bed sprayer

The sprayer is a self-contained unit that allows the user to spray trees and shrubs with the spray wand or broadcast spray in a 3.05-m (10-ft) swath with the spray boom.

Key features

• Shurflo pump operates at 6.9 bar (100 psi) and pumps 8 L/min (2.1 gpm)
• Spray boom is easily removed when not needed
• Fully adjustable brass spray wand tip achieves streams up to 9.15 m (30 ft)
• Mounts without the use of tools
• Brackets secure to Gator bed, no bungees required
• A built-in sump is provided to completely clean out the spray material
• Includes Gator accessory wiring harness, complete with quick-disconnects, for convenient electrical hookup
• Check valves in boom tips prevent siphoning and dripping
• Equipped with a 5.8-m (19-ft) hand wand hose for convenience
• Large threaded cap makes filling up easy
• Easy-to-read gallon marks are molded in

Ordering information

Contact your local John Deere dealer for availability and pricing information.

170-L (45-gal.) Gator bed sprayer
Order number: LP20851

340-L (90-gal.) Gator bed sprayer

The 340-L (90-gal.) Gator bed sprayer is designed to work with any Gator model with load capacities of 363 kg (800 lb) or greater. Extreme capacity is great for athletic fields, a farmette, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It comes complete with a 109-cm (43-in.) boom that sprays a 3.05-m (10-ft) swath. Engineered brackets secure the sprayer to the Gator bed with no tools or additional tie-downs required.

Special features:

• 340-L (90-gal.) capacity (custom brackets and plumbing combines two 170-L [45-gal.] tanks)
• Brackets secure to Gator bed, no tools or additional strapping required after initial setup
• Brackets allow boom height adjustment
• 8-L/min (2.1-gpm) Shurflo diaphragm-type pump with 6.9-bar (100 psi) shutoff can be run dry without damage
• Fully adjustable brass spray wand tip achieves streams up to 9.15 m (30 ft)
• Equipped with a 5.8-m (19-ft) hand wand hose with side mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• On/off switch located near operator
• 12-V plug included with wiring harness for convenient electrical hookup
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Specifications

Ordering information

Contact a local John Deere dealer for availability and pricing information.

340-L (90-gal.) Gator bed sprayer
Order number: LP20853

Viton is a trademark of The Chemours Company FC, LLC. Santoprene is a trademark of Exxon Mobil Corporation.

340.7-L (90-gal.) single tank sprayer

The high-performance (HP) single-tank 340.7-L (90-gal.) Gator bed sprayer is designed to work with Gator vehicles equipped with the deluxe cargo box that have a capacity in excess of 362.9 kg (800 lb). The custom molded 340.7-L (90-gal.) tank provides a low profile with capacity perfect for athletic fields, farmettes, commercial maintenance, or any large property. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. Custom engineered mounting hardware ensures the unit stays secure without the use of additional straps or tie-downs. Cover ground quickly with flexible boom options. (Boom sold separately).

High-performance features:

• 100 psi, 4-GPM diaphragm-type pump is designed for high-hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single-hand mist to 10.7-m (35-ft) stream.
• Side-mount hose tender for easy hose access and storage
• Glycerin-filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve for precise sprayer calibration

Additional features:

• Custom engineered brackets secure to Gator bed with no tools or additional straps
• Control valve channels spray to either the boom or spray wand
• Includes Gator accessory wiring harness, complete with quick disconnects, for convenient electrical hookup
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Shown on TH 6x4 with HP 45-gal. Sprayer

The standard Gator boom is compatible with all Gator sprayer models and is sold separately for the HP Gator sprayers. This fixed boom is conveniently sized at 43 in. (1.1 m) and does not extend wider than the Gator bed, but it is perfect for covering ground quickly and thoroughly with a 120-in. (3-m) spray swath.

The boom is ideal for basic spraying application. Three tips and check valves round out this offering (boom only, mounting brackets are provided with sprayers).

Boom Features:

• 43-in. (1.1-m) boom with three tips
• Check valves prevent siphoning and dripping
• Sold separately for:
  • HP 45-gal. Gator Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

Shown on TH 6x4 with HP 45-gal. Sprayer

Shown on TH 6x4 with HP 45-gal. Sprayer

The 150-in. (3.81-m) precision boom is compatible with the HP sprayers. This folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet™ nozzle bodies and commercial grade diaphragm check valves. The outer tips offer versatility with built-in shut offs to allow an adjustable 90-in. (2.3-m), 120-in. (3-m), or 150-in. (3.8-m) spray swath.

150-in. (3.8-m) precision boom features:

• Folding spring hinge
• Breakaway design
• Five TeeJet tips and nozzle bodies
• Adjustable spray swath (90 in., 120 in., 150 in.)
• 1/2-in. industrial-grade rubber hose
• Designed to work with
  • HP 45-gal. Gator™ Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

TeeJet is a registered trademark of Spraying Systems Company.

Shown on TH 6x4 with HP 90-gal. Sprayer

HP 90-gal. Sprayer

The 24-ft (7.3-m) boomless spray nozzles are compatible with all HP sprayers. This boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary. TeeJet™ nozzle bodies and commercial grade diaphragm check valves round out this offering.

Boomless spray nozzles feature

• Three TeeJet tips and nozzle bodies
• Commercial-grade diaphragm check valves
• 1/2-in. (12.7-mm) industrial-grade rubber hose
• Designed to work with all HP sprayers :
• HP 45-gal. Gator™ Bed Sprayer
• HP 90-gal. Gator Bed Sprayer
• HP 45-gal. Gator Bed Sprayer – XUV 550

 TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170- L) Tow-Behind Sprayer

The HP 45-gal. (170-L) Tow-Behind Sprayer offers the ultimate in performance and versatility. With a 45-gal. capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It is the perfect match for the customer who wants extreme performance. 

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options; a 150 in. (3.8 m) precision folding, 120-in. (3-m) standard three tip, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).

HP features:

• 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single hand mist to 35 ft (10.7 m) stream
• Front-mount hose tender for easy hose access and storage
• Glycerin filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve
• Includes sprayer remote control

Additional features

• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gal.)

Boom options (sold separately):

• 150-in. (3810-mm) precision spray boom
• 24-ft  (288-in.) boomless spray nozzles

SHURflo is trademark of SHURflo, LLC. TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170-L) tow-behind sprayer

The 45-gal. (170-L)  trail-type sprayer is equipped with a boom that sprays a wide, 120-in. width.

• Three nozzles for efficient broadcast spraying
• Boom folds up against the tank for storage

A 20-ft hose and handgun are provided.

• The 20-ft hose and handgun are helpful when spraying trees or other remote areas that cannot be reached with the sprayer itself
• A 14-in. wand on the handgun is standard equipment

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction.

• Low center of gravity gives excellent stability
• Equipped with a 4-position hitch
• Rear of the frame is designed so the sprayer will stand upright during storage to reduce the amount of space required

Additional features include:

• Diaphragm-type pump designed for high-hour commercial applications; it can be run dry without damage
• The spray wand is constructed of non-corrosive polypropylene material with Viton® components for remote spray jobs
• Two-wire fused wiring harness complete with quick-disconnects for convenient electrical hookup
• Large cap to easily fill up the tank
• Control valve to channel the spray to the boom or handgun
• Rugged translucent yellow tank with molded fill-level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

45-gal. (170-L) tow-behind sprayer
Order number: LP20485

SHURflo is a U.S.-registered trademark of SHURflo, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

0.3-m3 (10-cu ft) in-bed spreader for XUV825, XUV855, and HPX Utility Vehicles

Overview

The 0.3-m³ (10-cu ft) in-bed spreader easily expands the capabilities and productivity of operators with Gator XUV825 and XUV855 Full-Size Crossover and HPX Work Series Utility Vehicles. Featuring exclusive controls and ample hopper capacity, these spreaders are the ideal spreading solution to help operators quickly apply large amounts of ice melt materials.

Benefits

• Easily control the spreader with the 9-cm (3.5-in.) weatherproof, color display. Four push buttons are used to navigate functions including independent adjustment of the auger and spinner speeds, vibratory motor settings, reverse on the auger to clear out jammed material, and unload mode to completely empty the hopper. The display conveniently mounts in the hood latch opening on the vehicle's dash.
• Enjoy long periods of spreading ice melt materials with the ample volume of the 0.3-m³ (10-cu ft) poly hopper.
• The 7.6-cm (3-in.) diameter steel auger is powered by a direct-drive motor and features variable speed control, automatic jam clearing, and reverse to clear jammed material.
• Quickly cover large areas up to 9.1-m (30-ft) wide using the 30.5-cm (12-in.) diameter steel spinner with independent speed control.
  • The entire assembly can be quickly disconnected to access the hitch and reduce the spreader's overall footprint for storage.
• Eliminate bridged material inside the hopper with the vibratory motor that features four modes (pulse, low, high, and ramp).
• A top screen and fitted tarp are included to help with material handling. The top screen prevents clumped material from entering the hopper, while the fitted tarp keeps material dry.
• Get a dedicated, secure fit to the cargo box from the provided mounting hardware. Two stainless-steel tie-down rods secure the spreader to the tie-down hooks in the bed.

Additional details

The 0.3-m³ (10-cu ft) in-bed spreader is compatible with the following models:

• Model year 2018 and newer XUV825E, XUV825M, XUV855E, and XUV855M
• Model year 2017 and older XUV825i, XUV825i Power Steering, XUV855D, and XUV855D Power Steering
• Model year 2018 and newer HPX615E
• Model year 2017 and older HPX 4x4

17AT Cart

• 0.5-m ³ (17-cu ft) capacity
• 453.6-kg (1000-lb) load limit
• Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
• Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
• Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
• Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
• Heavy-duty polyethylene bed
  • Accepts dividers to separate cargo (template included)
• All-terrain knobby tires
  • Provides good flotation and traction in mud, sand, and other wet or soft areas
  • Flexes over bumps and ruts for a smoother, more controlled ride
  • Minimizes ground compaction to save turf and prevent ruts in soft ground
• Poly fenders to keep the operator, cart, and vehicle clean
• Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1.875-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
• Quality and styling compatible with other John Deere equipment

Ordering information

Contact your local John Deere dealer for availability and pricing information.

17AT Cart

Order number: LPPCT17ATJD

Fertilizer spreader

The Gator™ electric fertilizer spreader is the ideal solution for medium to large size jobs. This unit is engineered to fit heavy-duty XUV Gator Utility Vehicles and designed with a versatile hitch mechanism (sold separately) that allows quick and secure attach/detach capability for easy bed access or switching to a Gator salt spreader. Convenience is at the operator’s fingertips with an electronic variable-speed spinner and electronic gate control from the Gator seat. Adjustable flighting allows spread pattern control to make sure the material is applied where it is needed.

Features:

• Powder-coated steel frame
• Electronic variable-speed spinner
• Electrically actuated control of the flow gate
• 10-in. (25.4-cm) diameter spinner is stainless steel with adjustable flighting to control spreader pattern
• 8:1 ratio with bronze gear, grease filled
• Motor is 1/3 hp, 12-V DC, semi sealed

The mounting hitch and control box are sold separately, available through Order Zone.

Ideal for:

• Granular fertilizer
• Seed
• Granular pesticide
• Granular herbicide

Capacity:

• Volume: 3.0 cu ft (0.1 cu m)
• Weight: 240 lb (108.9 kg)
• Spreading width: up to 20 ft (6.1 m)

Includes:

• Side deflector

Compatibility:

• Compatible with all model year 2011 to current heavy-duty Gator XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles.
• Compatible with all XUV560 and XUV560 S4 Utility Vehicles.
• Gator XUV 620i and 850D Utility Vehicles and XUV 625i, 825i, and 855D Utility Vehicles pre model year 2011 must purchase the Gator hitch-mounting brackets, sold separately through Order Zone.

Ordering information

Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

Salt spreader

The Gator™ electric salt spreader is the ideal solution for medium to large size jobs. This unit is engineered to fit heavy-duty XUV Gator vehicles and designed with a versatile hitch mechanism (sold separately) that allows quick and secure attach/detach capability for easy bed access or switching to a Gator fertilizer spreader. The Gator salt spreader features an electric-driven auger for consistent salt presentation to the spinner. It draws power from the Gator vehicle, so no external power source is needed. It is powered by a variable-speed controller (sold with hitch) for precise spread pattern control. 

Features:

• Powder-coated steel frame
• Spinner motor controlled using the vehicle’s 12-V system
• 10-in. (25.4-cm) diameter spinner is nylon/glass reinforced resin for ultimate corrosion resistance
• 5:1 ratio with bronze gear, grease filled
• Motor is 1/3 hp, 12-V DC, semi sealed

The mounting hitch and control box are sold separately. Available through Order Zone.

Ideal for:

• Salt and large granular materials

Capacity:

• Volume: 3.0 cu ft (0.1 cu m)
• Weight: 240 lb (108.9 kg)
• Spreading width: Up to 20 ft (6.1 m)

Compatibility:

• Compatible with all model year 2011 to current heavy-duty XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles.

• Compatible with all Gator XUV560 and XUV560 S4 Utility Vehicles.

Gator XUV 620i and 850D Utility Vehicles and XUV 625i, 825i, and 855D Utility Vehicles pre model year 2011 must purchase the Gator hitch mounting brackets, sold separately through Order Zone.

Ordering information

Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

0.14-m3 (5-ft3) drop spreader

The Gator™ Drop Spreader features heavy-gauge stainless steel construction along with stainless-steel fasteners for exceptional durability in harsh conditions. The segmented rotor accurately meters material and evenly distributes material across the drop width. An industry-exclusive removable rotor tray allows for quick and easy clean out. Ideal for spreading large granular materials (such as rock salt). The 109-cm (43–in.) width is ideal for sidewalks and is suited well for snow and ice contractors, colleges and universities, hospital and health campuses, municipalities and schools, retirement home campuses, etc.

Features:

• Industry-exclusive removable rotor tray that simplifies cleanout and serviceability.
• No tools required to remove or install the rotor tray.
• Segmented stainless-steel rotor for accurate metering of material.
• Operator-controlled vibration motor to eliminate bridging of material.
• Rubber isolator mounts dampen tray vibration when operating vibration motor.
• Remotely mounted control box for power, vibration control, and variable rotor speed control (supplied with required Gator hitch and control package).
• Drivetrain is fully encased in stainless-steel shielding.
• Simplistic rotor drive with slotted chain adjustment plate.
• Six-position gate adjusts from fully closed to 38.1-mm (1 1/2–in.) clearance to meter a wide variety of products. Gate position can be adjusted without using tools.

Specifications:

• Volume: 5.0 ft³ (0.14 m³)
• Weight empty: 191 lb (87 kg)
• Weight full: 540 lb (245 kg)
• Spreading width: 43 in. (109 cm)

Spreader hitch assembly

The Gator™ hitch and electric control box for the salt/fertilizer spreader is engineered to fit your heavy-duty XUV Gator Utility Vehicles. This spreader hitch frame is designed with a versatile spring loaded mechanism to allow quick and secure attach/detach capabilities of your spreader. The hitch can easily be lowered, by the use of spring loaded pins, allowing the cargo box to be tilted.
 
Frame features:

• Powder-coated steel frame
• Spring-loaded easy hitch and release
• Lowers for easy bed access, dumping, and engine access

The electronic control box is designed to operate both the Gator fertilizer and salt spreader. The fully electronic control box accommodates a variable speed spinner control for both spreaders, and electronically actuated gate control for the fertilizer spreader. The weather-resistant box includes the switches, wiring and hardware for convenient dash mounting, allowing full control from the seat of the Gator.

Control box features:

• In-cab dash mount control box
• Variable speed control for spread width adjustment
• Electronically actuated gate controls on fertilizer spreader
• Sealed for weather resistance
• Large dial for spinner speed and gate control

Includes:

• Spreader hitch frame
• Electronic control box and wiring

Compatibility:

• Compatible with all model year 2011 to current heavy-duty XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles.
• XUV 620i and 850D Utility Vehicles and XUV 625i, 825i, and 855D Utility Vehicles pre model year 2011 must purchase the Gator hitch-mounting brackets, sold separately through Order Zone™.

Ordering information

Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

21 Steel Utility Cart

The 21 Steel Utility Cart is the ideal companion for the Gator™ Utility Vehicle:

• 454-kg (1000-lb) load limit
• Dump angle of 35/40 degrees
• Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
• Large pneumatic tires
  • Provide good flotation in mud, sand, and other wet or soft areas
  • Flex over bumps and ruts for a smoother, more controlled ride
  • Minimize ground compaction to save turf and prevent ruts in soft ground
• Unique bracket less tailgate means no side channels to obstruct materials when emptying
• When shoveling, recessed flat bolt heads stay out of the way
• Heavy-duty, reinforced one-piece solid undercarriage
• Contoured corner bed design
• Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gater™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models

Ordering information

Contact the local John Deere dealer for availability and pricing information.

21 Steel Utility Cart
Order number: LPUT21JD

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE large storage pouch - black

MOLLE large storage pouch - camo

MOLLE large storage pouch - brown

NOTE: Available through OrderZone.

The large MOLLE storage pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

MOLLE fire extinguisher pouch - black

MOLLE fire extinguisher pouch - camo

MOLLE fire extinguisher pouch - coyote brown

NOTE: Available through OrderZone.

The MOLLE fire extinguisher pouch is compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade rapid extraction clips
• Fits standard round 1.1-kg (2.5-lb) fire extinguishers
• Padded to protect contents
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 15.2-cm (6-in.) MOLLE sticks included
• Available in black, coyote brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Water bottle pouch with three color options

Overview

This water bottle pouch attaches to the backrest of utility vehicle seat covers that use the military-inspired modular lightweight load-carrying equipment (MOLLE) attachment system. The pouch fits up to a 0.95-L (32-oz) wide-mouth bottle.

Benefits

• Military-grade zipper and pull
• Constructed with military-grade CORDURA® fabrics
• Easily attaches with built-in straps
• Customizable with three colors: black, coyote brown, and Realtree EDGE™ camo
• Durable inner liner made of high-density coated pack cloth nylon fabric

Additional details

• Dimensions – 22.9 cm (9 in.) high, 10.2 cm (4 in.) wide, and 10.2 cm (4 in.) long
• Limited 1-year warranty
• Made in the USA

CORDURA is a trademark of INVISTA North America S.a.r.l. Realtree EDGE is a trademark of Jordan Outdoor Enterprises, Ltd.

Side-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Side-door opening toolbox features:

• 125-L (4.4-cu ft) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Door can also be used as a work bench when down
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 – olive and black
• BM26219 – camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model year 2018 and newer HPX615 and HPX815

MOLLE small storage pouch - black

MOLLE small storage pouch - camo

MOLLE small storage pouch - brown

NOTE: Available through OrderZone.

The small MOLLE storage pouches are compatible with bench seat covers and the operator protection system (OPS) MOLLE storage panel.

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade CORDURA® fabrics
• Utilizes the MOLLE attachment system
• Pair of 127-mm (5-in.) MOLLE sticks included
• Available in black, brown, or Realtree Hardwoods HD® camo pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made in the USA

Cordura is a trademark of INVISTA North America, LLC. Realtree Hardwoods HD is a trademark of Jordan Outdoor Enterprises, Ltd.

Shown assembled to OPS

Features of the soft rear screen and organizer:

• Instant shield against wind back draft, rain, and weather
• Protects against the worst winter weather
• Five mesh zippered cargo pockets for tools and gear
• Quickly attaches to the OPS with rip-and-grip straps
• Clear PVC window framed with heavy-duty fabric
• Cell phone or small gear holder
• Two large zippered compartments
• Two beverage pockets
• Stows all your essentials behind the seats
• Rolls up for storage

Compatible with: HPX, XUV 825i, XUV 825i S4, XUV 855D, and XUV 855D S4 Series Gator™ Utility Vehicles equipped with an occupant protection system (OPS).

Ordering information
Contact the local John Deere dealer for availability and pricing information.

Soft rear screen and organizer - black
Order number: LP93207

Top-door opening toolbox

This custom toolbox was specifically designed for users desiring more integrated sealed storage in a cargo box.

Top door opening toolbox features:

• 125-L (33-gal.) sealed storage
• Heavy-gauge sheet metal
• D-rings for tie downs
• Fully sealed lockable latch
• Sealed door
• Toolbox divider
• Removable tool tray
• Can be mounted on either side of the cargo box

The toolbox can be installed in minutes by simply removing the cargo box sides and tailgate, and bolting the toolbox onto the cargo box.

The toolbox requires the tailgate with brake and tail lights kit (BM26161) and optional label kit:

• BM26220 – green and yellow
• BM26218 –olive and black
• BM26219 – Camo

This toolbox is compatible with the following Gator™ Utility Vehicle models:

• TX
• TX Turf
• TE
• TH
• XUV625i
• XUV825i/E/M
• XUV825i/E/M S4
• XUV855D/E/M
• XUV855D/E/M S4
• XUV835E/M/R
• XUV865E/M/R
• Model year 2018 and newer HPX615 and HPX815

Gator track system

Play, work, and explore in all four seasons. Wheeled utility vehicles get buried very quickly in deep snow, swamps, sand, or muddy ground conditions. Adding a Camoplast® Tracks System will improve floatation and traction and will take you where wheels simply cannot go. Get true four-season capability without compromising winter performance with Camoplast track kits. Installed easily in one hour. And when the snow goes, switch back to wheels in an hour or less.

Camoplast has the only system on the market with anti-rotation on the rear spring that allows the rear of the track to swing upwards to climb on top of any difficult surface.

The fusable link on the anti-rotation system is designed to take the impact of every bump, jolt, and crash to prevent damaging your vehicle.

Drive sprockets designed specifically for use on the XUV.

Benefits of tracks include:

• All seasons capability - ideal for snow, mud, and marsh
• Easy steering - front radius track shape and carriage
• Increased vehicle stability while increasing ground clearance
• Drive sprockets matched to engine displacement

NOTE: Not compatible with standard straight blade, v-blade, front fender guards, rear bumper, and rear fender guards.

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Gator track system for XUV 855D
Order number: LP40897


Camoplast is a U.S.-registered trademark of CAMOPLAST Inc.

Front turn signals

Rear signal lights (taillight protectors not included)

Hazards switch (top)

Turn signal switch (right)

Key features

• Kit includes:

• Front/rear turn signals
• Hazards
• Backlit switches

NOTE: Not intended for use on public roadways.

Compatibility

• Compatible with all model year 2011 to current Gator™ XUV825 and XUV825 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Compatible with all model year 2011 to current Gator XUV625i, XUV855, and XUV855 S4 Utility Vehicles
• Also requires turn signal light harness kit
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

Front turn signals

Brake lights, taillights, reverse lights, and signal lights (taillight protectors not included)

Hazards switch (top)

Turn signal switch (right)

Key features

• Kit includes:

• Front/rear turn signals
• Brake lights, taillights, and reverse lights
• Hazards
• Backlit switches

NOTE: Not intended for use on public roadways.

Compatibility

• Compatible with model year 2017 to 2018 Gator™ XUV825, XUV825 S4, XUV855D, and XUV855D S4 Utility Vehicles
  • This kit also requires the turn signal light harness kit.
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Electrical harness requirements

1587.6-kg (3500-lb) winch (shown on XUV590)

This winch also requires a winch mount kit and a 50.8-mm (2-in.) front receiver with recovery loops.   Parts in the kit:

• WARN VRX 1587.6-kg (3500-lb) winch
• Roller fairlead assembly
• Hook
• Hook strap
• 3-m (10-ft) hand-held remote
• Winch contactor

WARN is a trademark of WARN Industries, Inc.

Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

• Effectively anchors to trees/boulders
• Change the pulling direction
• Double the pulling capacity

The accessories kit includes:

• Flexible tree strap
• Snatch block
• Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

Cordura is a trademark of INVISTA.

2041-kg (4500-lb) winch (chassis mounted)

Plug-in remote

Key features

• Impressive pulling capacity of 2041 kg (4500-lb)
• Equipped with a water-resistant contactor that supplies the amperage required for higher pulling capacities
• Includes a 3.05-m (10-ft), water-resistant, plug-in remote for safe distance operation that plugs directly into the glove box
• 15.2 m (50 ft) of 5.6-mm (7/32-in.) synthetic rope with hawse fairlead
  • Synthetic rope does not develop sharp burrs like steel rope and does not store as much potential energy when under load
• Ergonomic clutch handle
• Limited lifetime, 3-year electrical (North America) warranty offered through WARN

Compatibility

• Model year 2018 and newer XUV835 and XUV865 Utility Vehicles
• M-spec and R-spec vehicles come from the factory winch ready, and no additional attachment harnesses are required
• Requires winch mounting kit to mount the winch either on the chassis or on the front or rear receiver
• Not compatible with winch mounts BM26252 and BM26393

Electrical harness requirements

WARN is a trademark of WARN Industries, Inc.

Wireless winch remote

Wireless winch remote mounted on XUV835

Key features

• Wirelessly control winch from up to 15 m (50 ft) away
• Weatherproof transmitter has two large buttons, making it easy to operate even while wearing gloves
• Colored light-emitting diode (LED) lights provide clear operator feedback
• Kit includes wireless transmitter, receiver, holster, wiring, and mounting hardware

Compatibility

• Model year 2012 to current XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles
• Model year 2011 to current XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles
• Model year 2018 to current XUV835 and XUV865 Utility Vehicles

Bumper mount (winch not included)

The bumper mount kit includes all of the necessary wire harnesses, contactor mounts, and hardware to mount the WARN® VRX 1588-kg (3500-lb) winch (sold separately) to the front bumper of the heavy-duty XUV S4 models.

This kit is compatible with model year 2013 and newer XUV825 S4 and XUV855 S4 Gator™ Utility Vehicles.

WARN is a trademark of Warn Industries, Inc.

The bumper mount kit includes all of the necessary wire harnesses, contactor mounts, and hardware to mount the WARN® VRX 2041-kg (4500-lb) winch (sold separately) to the front bumper of the heavy-duty XUV S4 models.

This kit is compatible with model year 2014 and newer XUV825 S4 and XUV855 S4 Gator™ Utility Vehicles.

WARN is a trademark of Warn Industries, Inc.

Receiver mount (winch not included)

The receiver mount kit includes all of the necessary wire harness, contactor mounts, winch carrier, and hardware to be able to mount the WARN® VRX 1588-kg (3500-lb) winch (sold separately) to the front or rear receiver of the heavy-duty XUV S4 models.

The kit is compatible with model year 2013 and newer XUV825 S4 and XUV855 S4 Gator™ Utility Vehicles.

WARN is a trademark of WARN Industries, Inc.

Protective window and essential organizer all in one

Features:

• Heavy-duty fabric coated for maximum water resistance and repellency
• Quickly attaches to the OPS with rip-and-grip straps
• Stows all essentials behind the seat
• Multiple pockets for added storage
• Super-clear vinyl windows are cold crack tested to -20°C
• Rolls up for storage
• Two-year warranty

Ordering information:
Available through Order Zone. Contact the local John Deere dealer for availability and pricing information.

OPS rear screen on Gator™ XUV 825i (front view)

OPS rear screen on Gator XUV 825i S4 (rear view)

Product attributes

• Provides additional protection to the operator and passenger
  • NOTE:  Never carry loads in cargo box over load guard
• Includes headrests for additional comfort with the bench and bucket seats
• Perforated, black metal screen easily attaches to the side and upper tubes of the OPS with four quick clamps
• Compatible with the following models:
  • HPX: Model year 2013-current
  • XUV 625i:  Model year 2013-current
  • XUV 825i and 825i S4:  Model year 2013-current
  • XUV 855D and 855D S4:  Model year 2013-current
• Not compatible with pre-model year 2013 HPX and XUV’s, including 620i and 850D

Abrasion-resistant full windshield

The abrasion-resistant full windshield features:

• Quick-clamp mounting system – tool-free installation and removal in seconds
• Manufactured from super-premium, two-sided Makrolon® AR grade abrasion-resistant polycarbonate
• Increased ultraviolet (UV) longevity – resists yellowing longer than optical-grade polycarbonate
• Increased chemical resistance over traditional optical-grade polycarbonate
• Almost as hard as glass with greater impact strength
• Bottom portion flips up and secured in place by two ball studs

Makrolon is a trademark of Bayer Aktiengesellschaft.

Abrasion-resistant half windshield

The abrasion-resistant half windshield features:

• Quick-clamp mounting system - tool-free installation and removal in seconds
• Manufactured from super-premium, two-sided Makrolon® AR grade abrasion-resistant polycarbonate
• Increased ultraviolet (UV) longevity – resists yellowing longer than optical-grade polycarbonate
• Increased chemical resistance over traditional optical-grade polycarbonate
• Almost as hard as glass with greater impact strength

Makrolon is a trademark of Bayer Aktiengesellschaft.

Glass windshield with wiper

Glass windshield with wiper (vent open)

Required operator protection system (OPS) switch bank

The glass windshield with wiper features:

• Quick-clamp mounting system - easy installation and removal in seconds
• Laminated, E-mark glass
• The lower section of the windshield seals nicely against the vehicle’s hood to protect occupants from the harshest of elements. It also flips up and is secured by rubber straps to allow increased airflow into the passenger area.

The windshield requires an OPS switch bank (sold separately) to mount the switch.

Reservoir bottle

Spray nozzle

Especially useful for working around properties and job sites, the windshield washer kit includes these components:

• Mounting hardware
• Spray nozzle
• Large reservoir with electric pump, harness, and hose
• Three-position backlit rocker switch: off, wiper, washer

The reservoir assembly bolts to the frame. A convenient three-position rocker switch controls the windshield wiper and washer fluid. As with all Gator™ Utility Vehicle electrical kits, the washer kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

• All Gator model year 2011-current HPX, XUV 625i, XUV 825i, XUV825i S4, XUV 855D, XUV855D S4, and M-Gator A3 Utility Vehicles
• All Gator model year XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles