Rotary Cutters | RC10R Rotary Cutter

Features

What is the best cutter for your job?

NOTE: Only for single spindle and multi-spindle.

John Deere rotary cutters lead the way with innovative design, superior performance, and proven durability. Valuable features such as the Double-Decker™ design and Max Flow cutting chamber prevent water and debris from accumulating on the smooth, dome-shaped top deck while the flat bottom deck absorbs the punishment from rocks and stumps.

The top deck stays smooth - no dents, no dings, no holes. The internal supports sandwiched between the top and bottom decks are key to the smooth and structure-free Max Flow cutting chamber, while at the same time provide added strength and durability.

To help promote safe operation, John Deere rotary cutters are equipped with front and rear safety-chain shields. John Deere rotary cutters continue to advance in value with powerful gearboxes, blade holders, and compatibility with a wide range of tractors.

Here are situations when a rotary cutter provides value:

Clipping pastures encourages grass growth, optimizing valuable pasture acreage.
Cutting grass and stalks helps control insects.
Routine cutting keeps weeds from reseeding.
It is the most cost efficient way to cut roadsides, parks, cemeteries, airport fields, hydro, gas, and telephone easements, and all other types of open properties.
Cutting grass waterways encourages root development and helps prevent erosion.
Knocking down stalks such as cotton, corn, or milo speeds up decomposition. This is essential in no-till and minimum-till fields.
Clearing out brush.
Control undergrowth and grass in orchards, vineyards, and groves.

Decide what model to use based on:

The size of the area to mow versus the size of the machine – the bigger the area to mow, the bigger the mower needs to be in order to be efficient during mowing hours. Similarly, the limitation of a small area will guide operators to use a smaller mower.
The amount of time and frequency it will be used – for longer hours and more frequency, choose a heavier duty machine.
Tractor compatibility – if there is a tractor the operator will be using, look for the tractor compatibility sheet to identify appropriate options.

John Deere rotary cutters are available in two duty-level categories:

Mid-duty
- RC M models are available in 1.5-m (5-ft), 1.8-m (6-ft), 2.1-m (7-ft), 2.5-m (8-ft), and 3.2-m (10-ft).
- This duty-level category cuts brush up to 50.8 mm (2 in.) in diameter.
Heavy-duty
- RC R models are available in 3.2-m (10-ft) and 4.2-m (14-ft).
- This duty-level category cuts brush up to 76.2 mm (3 in.) in diameter.
- RC6R is available in 1.8-m (6-ft) and the RC7R is available in 2.1-m (7-ft) cut widths; they cut brush up to 101.6 mm (4 in.) in diameter.

NOTE: R Series are heavier built to cut at a 101.6 mm (4 in.) capacity level more frequently and for longer durations.

John Deere Double-Decker™ design for superior frame strength

Cross-section of Double-Decker design

Replaceable bolt-on skid shoes

The patented Double-Decker design improves strength and cutting performance while reducing top deck rust. Two welded decks include a 3-mm (11-gauge, 0.118-in.) to 3.5-mm (10-gauge, 0.138-in.) thick upper deck, depending on the model, and a 3-mm (11-gauge, 0.118-in.) to 4.5-mm (7-gauge, 0.177-in.) thick lower deck, depending on the model.

Internal stiffeners are sandwiched between the decks to add extra strength and rigidity.

The Double-Deck design also provides a sturdy base to support the gearcases. Gearcases need this sturdy base to resist the bending loads imposed upon them when blades contact immovable objects or the ground.

The bottom deck is the main defense against rocks and field debris, to help protect the top deck from impacts so it will retain its smooth form.

Each side skirt includes replaceable bolt-on skid shoes.

Gearcases and blade holders provide better performance

Gearcase and blade holder shown

The John Deere RC gearboxes:

Large seals
Large housing
Large output shaft
Precision forged bevel gears
Large bearings
Stump jumper

RC gearcases and blade holders provide the following:

More horsepower
Faster blade-tip speed
Better performance
Quieter operation
Increased durability

Larger, more durable gearboxes

RC10R gearcases

Gearcases are John Deere engineered for reliability and dependability.

Transfer (center gearcase) – 120 continuous hp or 180 peak hp
Outer gearcases – 100 continuous hp or 140 peak hp

Heavy-duty, tapered roller bearings and precision gears help ensure long life.

Output shafts are splined, not just keyed, for extra strength and durability.

The RC10R model comes standard with five year warranty.

Blades ensure clean cutting and fine shredding

Suction blades

Suction blade

Suction blades provide additional lift action for picking up downed material. The blades are 1.3 cm x 10.2 cm (0.5 in. x 4 in.) in size and heat-treated for long wear life.

A fast blade-tip speed (up to 16889 fpm) ensures clean cutting and fine shredding of material.

Flat blades

Flat blade

Flat blades are effective for any materials not downed and require suction for lifting.

Flat blades require less horsepower and have a cutting edge on both sides. Only available with double-blade system.

Dual blades (bar-type blade holder only)

Dual blades

Dual blades are effective for increased shredding of crop residue.

The dual blades consist of a 1.3-cm x 10.2-cm (1/2-in. x 4-in.) lower suction blade and a 1.3-cm x 7.6-cm (1/2-in. x 3-in.) upper suction blade.

Tractor hookup available in two configurations

Lift type

Lift type (shown with iMatch™ hitch system)

The lift-type versions fit tractors with Category 2, 3, or 3N 3-point hitches (with or without Quick Hitch).

NOTE: The lift-type versions require a larger tractor than other versions. For RC10R Lift-Type Rotary Cutters, the minimum-size tractor recommended is a 6020 Series or equivalent. For RC14R Lift-Type Rotary Cutters, the minimum-size tractor recommended is a 7720 or equivalent. Refer to the tractor's operator's manual for ballasting instructions. The pull-type versions of the RC10R Multi-Spindle Rotary Cutter require a tractor with a minimum of 50 power take-off (PTO) hp. The RC14R pull-type versions require a tractor with a minimum of 60 PTO hp. Note that the type and volume of material being cut affect horsepower requirements.

Pull type

Parallel lift linkage helps keep the cutter level through all height adjustments. Cylinders are John Deere manufactured, meaning more reliability and durability.

Warranty

Five-year limited gearbox warranty provided on every John Deere rotary cutter

Five-year warranty on all flex-wing gearboxes

Five-year warranty on all rotary cutter gearboxes

John Deere is so confident in the reliability of the gearbox that rotary cutters come with a 5-year limited gearbox warranty.

There is also 1-year warranty on the complete machine, including drivelines, clutches, and many other components.

Show More Show Less

Specs & Compare

Select up to 4 models to compare specifications

John Deere

RC10R

Rotary Cutter

Cutting width

3,200 mm
126 in.

Cutting height

25 to 305 mm
1 to 12 in.

Cutting capacity

76.2 mm
3 in.

Cutting chamber Depth

267 mm
10.5 in.

Tractor PTO HP range

Minimum pull-type 37 kW
50 hp
Minimum PTO lift-type 60 kW
80 hp

Tractor PTO

540 rpm

Type

Lift-Type, Pull-Type (Pull-Type has standard 10,000 lb; 4,539 kg, Safety Tow Chain)

Date collected

No money down and competitive financing†

on New John Deere Rotary Cutters

†For complete details regarding this offer, please select the corresponding link below.

View Offer Details

Up To 20% OFF Rotary Cutter Blades†

for various rotary cutter models.

†For complete details regarding this offer, please select the corresponding link below.

View Offer Details

12% OFF Select Attachments†

for Round Balers & Rotary Cutters

†For complete details regarding this offer, please select the corresponding link below.

View Offer Details

Show More Show Less

Transport width	3,350 mm 132 in.
Overall width	3,350 mm 132 in.
Overall length	4,040 mm 159 in.
Deck shape	Domed
Deck type	Double decker
Deck thickness	Upper 3.5 (10) mm 0.141 (10) in. Lower 3.5 (10) mm 0.141 (10) in.
Side skirt thickness	6 (3) mm 0.25 (3) in.
Approx. weight	1,057 kg 2,326 lb

Size	Main ASAE Category 5; lift-type ASAE Category 4; pull-type
Protection	Main Non-seize, slip-clutch driveline pull-type has equal-angle Category 4 driveline Connecting Shock absorbing shafts

Thickness	13 mm 0.5 in.
Width	102 mm 4 in.
Type	Suction
Overlap	75 mm 2.8 in.
Blade tip speed	540 RPM 5,148 m/min 16,889 fpm 309 km/h 192 mph
Material flow system	Max flow
Holder	Type Round stump jumper

Type	Laminated (Pull-type has severe-duty Ag tire option)
Row width adjustment	Yes

Blade tip speed - 540 rpm
Cutting capacity
Cutting width
Deck thickness - Upper - Lower
Drivelines - Size - Main
Hitch - Category
Protection - Main
Shielding - front/rear
Side skirt thickness
Tractor PTO HP range

RC10RRotary Cutter